The Scope and Purpose of a Home Inspection
Purchasing property involves risk
The purpose of a home inspection is to help reduce the risk associated with the purchase of a structure by providing a professional opinion about the overall condition of the structure. A home inspection is a limited visual inspection and it cannot eliminate this risk. Some homes present more risks than others. We cannot control this, but we try to help educate you about what we don’t know during the inspection process. This is more difficult to convey in a report and one of many reasons why we recommend that you attend the inspection.
A home inspection is not an insurance policy
This report does not substitute for or serve as a warranty or guarantee of any kind. Home warranties can be purchased separately from insuring firms that provide this service.
A home inspection is visual and not destructive
The descriptions and observations in this report are based on a visual inspection of the structure. We inspect the aspects of the structure that can be viewed without dismantling, damaging or disfiguring the structure and without moving furniture and interior furnishings. Areas that are concealed, hidden or inaccessible to view are not covered by this inspection. Some systems cannot be tested during this inspection as testing risks damaging the building. For example, overflow drains on bathtubs are generally not tested because if they were found to be leaking they could damage the finishes below. Our procedures involve non-invasive investigation and non-destructive testing which will limit the scope of the inspection.
This is not an inspection for code compliance
This inspection and report are not intended for city / local code compliance. During the construction process structures are inspected for code compliance by municipal inspectors. Framing is open at this time and conditions can be fully viewed. Framing is not open during inspections of finished homes, and this limits the inspection. All houses fall out of code compliance shortly after they are built, as the codes continually change. National codes are augmented at least every three years for all of the varying disciplines. Municipalities can choose to adopt and phase in sections of the codes on their own timetables. There are generally no requirements to bring older homes into compliance unless substantial renovation is being done.
Environmental/Mold Exclusions
The reported or actual health effects of many potentially harmful, toxic or environmentally hazardous elements that may be found in building materials or in the air, soil, water in and/or around any house are varied, and, in some cases controversial. A home inspection does not include the detection, identification or analysis of any such elements or related concerns such as, but not limited to, mold, allergens, legal/illegal drugs and other biological contaminants, radon, , bed bugs, cockroaches, fleas, lice, formaldehyde, asbestos, lead, electromagnetic fields, carbon monoxide, insecticides, Chinese drywall, refrigerants and fuel oils. Furthermore, no evaluations are performed to determine the effectiveness or appropriateness of any method or system (e.g., water filter, radon mitigation, etc.), designed to prevent or remove any hazardous or unwanted materials or elements. An environmental health specialist should be contacted for evaluation of any potential health or environmental concerns. The noting of the presence of materials commonly considered to contain asbestos, formaldehyde, lead, mold etc in the inspection report, should not be construed to mean the inspector is inspecting for these things but instead should be seen as a "heads-up" regarding these materials and further evaluation by qualified professional may be warranted.
This is just our opinion and just for you
The contents of this report are for the sole use of the client named above and no other person or party may rely on this report for any reason or purpose whatsoever without the prior written consent of the inspector who authored the report. Any person or party who chooses to rely on this report for any reason or purpose whatsoever without the express written consent of the inspector does so at their own risk and by doing so without the prior written consent of the inspector waives any claim of error or deficiency in this report.
Construction techniques and standards vary. There is no one way to build a house or install a system in a house. The observations in this report are the opinions of the home inspector. Other inspectors and contractors are likely to have some differing opinions. You are welcome to seek opinions from other professionals.
The scope of this inspection
The inspection and report are intended to provide the client with information regarding the condition of the systems and components of the property as observed at the time of the inspection. The inspector examines the readily accessible systems and components using normal operating controls. The inspection is not technically exhaustive and will not identify concealed conditions or latent defects. Any comments offered by the INSPECTOR that could be construed as over or beyond the standards of practice or the language of this contract, are offered as a professional courtesy. Refer to the Washington State, Standards of Practice and/or Pre-Inspection Agreement for additional information regarding the scope and limitations of the inspection. The Standards of Practice are linked below and describe the "minimum" standards a Licensed Washington State Home Inspector must adhere to: WA SOP.
All homes are likely to have some faults which may range from cosmetic defects to major safety hazards. Not all defects will be found. While some minor deficiencies may be mentioned, the emphasis of this report is to inform the buyer of the property condition by detecting deficiencies or circumstances that may affect the structural integrity of the building and its components and its safe use as a residence.
You are encouraged to obtain competitive estimates for major repair needs. Safety and health issues should be addressed promptly. It is recommended that all corrective work, other than routine maintenance activities, be performed by qualified licensed contractors.
It is beyond the scope of the Standard Home Inspection to identify components within the home that may have been part of a "manufacturer's recall". Mention of specific recalls within this report must not be construed to mean that all such items have been identified, or that such identification is part of a Standard Home Inspection. When possible, appliance Model Numbers and Serial Numbers are included in the report and can be used to check for recall related issues. If you have any question about specific appliances, information can be found at the CPSC (Consumer Products Safety Commission) website: https://www.cpsc.gov, or contact the manufacturer directly.
It is recommended that you obtain as much history as is available concerning this property. This historical information may include copies of any seller's disclosures, previous inspection or engineering reports, reports performed for or by relocation companies, municipal inspection departments, lenders, insurers and appraisers. You should attempt to determine whether repairs, renovation, remodeling, additions or other such activities have taken place at this property, and this report will attempt to identify such items when possible.
Ranges, Dish Washers, and Refrigerators (and the like) are typically tested for basic function (Do they turn on). No assertions are made as to how well they function. Microwave ovens, clothes washers/dryers are not operated.
Throughout this report, comments will be made as to the presence or absence of components or parts of components. This must not be construed to mean that these components or parts of components exist (or don't exist) in concealed areas or behind finished surfaces. For example: if foundation bolting was seen in one area, it does not mean that the bolting exists (or doesn't exist) in areas that are concealed. Also if an item was noted as "not being visible," that should not be construed to mean that none of whatever was "not visible" does not exist on the premises---it just means none was noted at the time of inspection and should be seen as a "heads-up" that the concern or condition might be present but hidden, or that the conditions that would allow its presence to be known was not replicated at the time of inspection.
Many of the non-narrative observations/documentation detailed in the report that are related to more "cosmetic" issues should not be construed as "all inclusive" but should instead be seen in as "suggestive" or a "guideline" of conditions that may exist elsewhere in the home. It is not the focus of the report to comment extensively on cosmetic issues, but I do make note of them at times to help complete the "snap-shot" of the home at the time of inspection. For example, "nail-pops" seen in one room are likely to be seen (and should be anticipated) in other rooms even though I may not have noted them in the report.
Throughout the report I may make recommendations as to possible repairs. These recommendations are not intended to be substitutes or construed to be more appropriate than the recommendations of the professionals making the repairs. Conflicts in recommendations should be resolved prior to repairs being made.
Who should make repairs and what should their qualifications be?
Contractor qualifications: In the text of the report, in some instances, I recommend that work be done by a "qualified" person or "qualified" parties. I consider qualified parties, in licensed trades, to be those individuals who hold the necessary licenses to legally work in their profession -- licensed electricians, licensed pest control applicators, licensed plumbers, licensed HVAC professionals, licensed engineers, licensed general contractors, etc. In instances where a task may not, typically, need to be done by a person with a license, my recommendation is to hire an individual to do the work who is, based on past training, experience or expertise, qualified to further evaluate the condition or problem listed in the report and to then make appropriate repairs.
Photography/Infrared and Moisture meters used
Digital photographs, thermographs and illustrations may be included in this report. If included, their purpose is to better illustrate an observation or recommendation. No degree of importance should be inferred by the presence or absence of photos and illustrations. Some pictures will undergo lightening, darkening, cropping and have callouts and other "overlays" present, but the image itself will not be altered unless specifically noted on the picture. The use of infrared thermography (IR) must not be construed to mean that a full thermal survey of the structure was done. The use of IR is primarily for recording thermal differences to show the function or lack of function of heating and cooling of HVAC equipment; and, anomalies associated with temperature differences sometimes produced by water leaks, air infiltration etc. IR during a home inspection is mainly a qualitative evaluation and, in most cases, "thermal tuning" will not have been performed and therefor temperatures present on any thermal images in the report should not be seen as an absolute temperature but only "relative temperature."
Throughout the report, reference may be made to moisture conditions and percentages of moisture content. These moisture readings are obtained by the use of a Protimeter Surveymaster Moisture Meter.
Your participation is requested
Your presence is requested during this inspection. A written report will not substitute for all the possible information that can be conveyed verbally by a shared visual observation of the conditions of the property. If you were not present during the inspection, you are urged to contact the inspector for a verbal consultation. I am happy to speak on the phone or a similar method to go through areas of concern in the report. If you choose not to consult with the inspector, West Inspect LLC cannot be responsible for misinterpretation of the report.
How to Read This Report
Getting the Information to You
This report is designed to deliver important and technical information in a way that is easy for anyone to access and understand. If you are in a hurry, you can take a quick look at our "Summary Page” and quickly get critical information for important decision making. However, we strongly recommend that you take the time to read the full Report, which includes digital photographs, captions, diagrams, descriptions, videos and hot links to additional information.
The best way to get the layers of information that are presented in this report is to read your report online, which will allow you to expand your learning about your house. You will notice some words or series of words highlighted in blue and underlined – clicking on these will provide you with a link to additional information.
This report can also be printed on paper or to a PDF document.
Create Request List Function
The "Create Request List" function, located under the report header, allows any party to build a request list from any of the items in the report. These lists can then be given to appropriate parties as desired.
Chapters and Sections
This report is divided into chapters that parcel the home into logical inspection components. Each chapter is broken into sections that relate to a specific system or component of the home. You can navigate between chapters with the click of a button on the left side margin.
Most sections will contain some descriptive information done in black font. Observation narrative, done in colored boxes, will be included if a system or component is found to be significantly deficient in some way or if we wish to provide helpful additional information about the system or the scope of our inspection. If a system or component of the home was deemed to be in satisfactory or serviceable condition, there may be no narrative observation comments in that section and it may simply say “tested,” or “inspected.”
Observation Labels
All narrative observations are colored, numbered and labeled to help you find, refer to, and understand the severity of the observation. Observation colors and labels used in this report are:
- Primary Concern:Significant concerns that need prompt evaluation and repair by a qualified professional, such as safety hazards, water intrusion, or structural issues.
- Repair/Replace:Items that need repair but are not urgent safety or damage concerns. Some may be larger projects, such as refinishing hardwood floors, but are listed here because they are mainly cosmetic or functional. Have them addressed by a qualified professional as needed.
- Minor Repair:Minor concerns or items typical for the age of the home. In my opinion these are not urgent, but should be addressed by a qualified professional as time allows.
- Recommended Maintenance:Routine maintenance items, such as servicing the furnace, cleaning the gutters or replacing furnace filters. These are normal parts of home ownership and should be done on a regular schedule.
- Improvements & Upgrades:Recommended upgrades that are not defects, but could improve safety, efficiency or reliability. This includes items in older homes that were acceptable when built but fall short of current standards. These are optional and can be done at your discretion.
- Due Diligence:Conditions that need further evaluation by a qualified specialist to determine their severity and the urgency of any repairs, such as a possible buried oil tank. Have these evaluated before closing.
- Inspection Notes & Limitations:General information and limitations of the inspection, including areas that could not be fully inspected. These are not defects.
- Description:Descriptions of the home's systems and components as observed during the inspection, such as materials, types and ages. These are for reference and are not defects.
- Pest Conditions:Conditions related to pests, including signs of activity, entry points and related damage. A licensed pest control operator should evaluate and treat as needed.
Summary Page
The Summary Page is designed as a bulleted overview of all the observations noted during inspection. This helpful overview is not a substitution for reading the entire inspection report. The entire report must be read to get a complete understanding of this inspection report as the Summary Page does not include photographs or photo captions.
Moisture Meter Testing
Where moisture meter testing is indicated in this report a Protimeter Surveymaster Dual Function was used.
The Full Report
Grounds
Drainage & Site Information
Driveways/Walkways/Flatwork
Stairs & Railings
Grounds, Trees & Vegetation
Roof, Chimney & Gutters
Roofing
Chimneys
Skylights & Sunroom
Roof Ventilation
Gutters & Downspouts
Roof Limitations & Exclusions
Electric Service
Electric Service Permits Found
Electric Service Voltage Tested
Electric Service
Circuit Breaker Identification
Service Equipment
Electrical Grounding System
Electrical Bonding System
Electric Distribution & Finish Wiring
Branch Wiring
Wiring, Receptacles & Fixtures
Ceiling Fans
Low Voltage Wiring
HVAC & Ventilation
Heating & Cooling Systems
Air Filters
Heating & Cooling Distribution Systems
Mechanical Ventilation Systems
Solid Fuel Fireplaces
Interior
General Information
Floors and Floor Materials
Walls, Ceilings, Trim and Closets
Wall Insulation and Air Bypass
Stairs and Railings
Interior Doors
Windows
Windows - Older
Smoke & Carbon Monoxide Alarm Systems
Pest Related Conditions
Kitchen
General Kitchen Photos
Sinks and Faucets
Cabinets and Countertops
Ventilation Method
Appliances
General Kitchen Condition
Primary Bedroom Bathroom
General Bathroom Photos
Sinks and Cabinets
Toilet
Bathtub / Shower
Bathroom Ventilation
General Bath Condition (Finishes, Walls, Flooring, etc)
Upstairs Hallway Bathroom
General Bathroom Photos
Sinks and Cabinets
Toilet
Bathtub / Shower
Bathroom Ventilation
General Bath Condition (Finishes, Walls, Flooring, etc)
Basement Bathroom
General Bathroom Photos
Sinks and Cabinets
Toilet
Bathtub / Shower
Bathroom Ventilation
General Bath Condition (Finishes, Walls, Flooring, etc)
General Comments
Building Characteristics, Conditions and Limitations
Type of Building: Single Family (1-story with Basement)
Approximate Square Footage: 2700
Approximate Year of Original Construction: 1958
Attending the Inspection: Buyer and Buyer's Agent
Occupancy: Unoccupied
Weather during the inspection: Clear, Partly Cloudy
Approximate temperature during the inspection: Below 60[F]
Ground/Soil surface conditions: Damp
For the Purposes of This Report - The Front of the Home Faces: The Driveway (Front Side), East
Residential Homes: Due Diligence Information, Building Orientation
During the inspection, I am looking for obvious, and not so obvious, clues as to problems with components or systems. At times, a repair can be as involved as replacement and sometimes additional problems or damage are found when work begins. In fact, a defect in one system or component can cause a related problem at another location that was not apparent at the time of the inspection. It is recommended that you obtain -- at a minimum -- evaluations from specialists for service/repairs or replacement/upgrades of any components or systems that may be potentially dangerous or complex to fix or replace--in a time frame consistent with proper due diligence.
If repairs are completed in an acceptable time frame, you will minimize chances of any unexpected surprises after closing. In performing one's due diligence, it is important the client not only follow through on the recommendations I make in this report but any other concerns that may arise when called for repairs.
This report should never be taken as an end in itself, but merely part of the "process" of due diligence. It is in no way meant to interfere with the decisions you must make in order to move forward with the transaction, it is merely what I consider best advice.
- While on-site, all professional repair persons should be asked to further evaluate the condition of the system, structural components, or device that he or she is working on. Often one problem will lead to another related issue which can require further repairs or replacement. If remodeling is done, where walls and ceilings are opened, wallpaper removed, homeowners may find some concealed issues that will also have to be addressed during the remodel. Because the home inspector is a generalist, this policy further protects the client.
Building Orientation: All points of reference "left, right, front and back," are as you face the front of the building, while viewing it from the exterior. All photos that are referenced in the report, are a representative sample of the conditions and / defects that were discovered. Not every condition or defect was photographed.
Covenants, Easements and Encumbrances: Present
Properties sometimes have covenants and easements and other encumbrances associated with them. This inspection makes no attempt at identifying or providing information regarding any such issues, but will mention observed "community" issues that may affect the property. I recommend discussing any such concerns with the seller. Typical concerns include, but are not limited to: utility easements, height restrictions, maintenance of underground drainage, etc. No determination is made as to whether this property is part of a homeowner association.
Codes, Standards, and Manufacturer's Instructions: Information
This inspection and report are not intended for city / local code compliance. During the construction process, depending on the age of the home, structures are inspected for code compliance by municipal inspectors. Framing is open at this time and conditions can be fully viewed. Framing is not open during inspections of finished homes, and this limits the inspection. All houses fall out of code compliance shortly after they are built, as the codes continually change. National codes are augmented at least every three years for all of the varying disciplines. Municipalities can choose to adopt and phase in sections of the codes on their own timetables. There are generally no requirements to bring older homes into compliance unless substantial renovation is being done. That said, most recommendations get guidance from codes, manufacturer's instructions and other authoritative sources.
In the report there may be instances where specific building codes, other standards and manufacturer's instructions may be specifically quoted. This in no way should be construed to mean this inspection is a code compliance inspection or that all manufacturer's instructions are known or checked. These instances are only provided as a courtesy in assisting with specific instances. There may be other exceptions to these examples that are also applicable and a full evaluation by the appropriate trade is recommended.
Microbial Growth: Information
The Standard Home Inspection does not attempt to identify whether the type of Mold or what looks like Mold seen on the premises are of types considered to have adverse health effects. Concerns regarding the toxicity of Mold is deferred to qualified Industrial Hygienists who should be contacted regarding any concerns that you might have about Mold found on the property. Please see the information below regarding Mold from the EPA.
Mold (a type of fungus) is a wood inhabiting organism, not a wood destroying organism.
Ten Things You Should Know About Mold (from the EPA):
- Potential health effects and symptoms associated with mold exposures include allergic reactions, asthma, and other respiratory complaints.
- There is no practical way to eliminate all mold and mold spores in the indoor environment; the way to control indoor mold growth is to control moisture.
- If mold is a problem in your home or school, you must clean up the mold and eliminate sources of moisture.
- Fix the source of the water problem or leak to prevent mold growth.
- Reduce indoor humidity (to 30-60% ) to decrease mold growth by: venting bathrooms, dryers, and other moisture-generating sources to the outside; using air conditioners and de-humidifiers; increasing ventilation; and using exhaust fans whenever cooking, dish-washing, and cleaning.
- Clean and dry any damp or wet building materials and furnishings within 24-48 hours to prevent mold growth.
- Clean mold off hard surfaces with water and detergent, and dry completely. Absorbent materials such as ceiling tiles, that are moldy, may need to be replaced.
- Prevent condensation: Reduce the potential for condensation on cold surfaces (i.e., windows, piping, exterior walls, roof, or floors) by adding insulation.
- In areas where there is a perpetual moisture problem, do not install carpeting (i.e., by drinking fountains, by classroom sinks, or on concrete floors with leaks or frequent condensation).
- Molds can be found almost anywhere; they can grow on virtually any substance, providing moisture is present. There are molds that can grow on wood, paper, carpet, and foods.
Helpful Links
- Mold information from the EPA and MOLD,
- The following link is a very good "practical" video about dealing with mold in the home: NW Clean Air Agency.
- The following link is a very good source for the most current information regarding mold in the home: Health Effects of Indoor Mold.
Re-Inspections: Information
After repairs are made to the home, I recommend hiring me for a follow-up to ensure satisfactory corrections. A minimum evaluation fee of $275-$325 applies for each requested re-inspection service. Any further documentation beyond email responses and evaluations will incur additional charges, to be agreed upon when scheduling further assessments. REMEDIAL WORK – For any component or condition requiring attention, it's wise to have it evaluated by qualified specialists or contractors before closing to determine the full scope of any needed repairs. Hidden concerns or consequential damage may exist. In case further remedial work arises post-inspection, contact West Inspect LLC for a preliminary assessment before proceeding with repairs.
- IF THERE ARE ITEMS WITHIN THIS REPORT THAT REQUIRE RE-INSPECTION, YOU ARE ENCOURAGED TO HAVE ME COMMUNICATE DIRECTLY WITH THOSE HIRED TO MAKE THE CORRECTIONS TO ENSURE THAT REPAIRS ARE PROPERLY MADE.
- Numerous improvements can enhance safety and living conditions in any home. While many of these issues surface during the Standard Home Inspection, there are likely additional enhancements that can be made. For more information, visit the Center for Healthy Living.
* REAL ESTATE AGENTS *: What is "Create Request List"?
The Create Request List feature, found at the top of the report, lets agents and clients quickly build a custom list of selected inspection findings—such as repairs, maintenance items, or upgrades. To use it, open the report, check any items you’d like to include, scroll to the bottom, and select Create Request List. This generates a clean, shareable PDF containing only those chosen details.
This tool is especially helpful for agents preparing repair requests or negotiating after an inspection. You can easily share only the relevant items—like deck or roof repairs—with sellers or contractors without sending the full report. It keeps communication focused, organized, and professional.
At the time of inspection, this property was unoccupied. Vacant properties present unique challenges for home inspections, particularly regarding plumbing and electrical systems that have not been in regular use. While these systems can be tested during the inspection, it's important to note that a one-time assessment differs significantly from regular use, making it difficult to predict how these systems will perform under normal conditions post-inspection.
Potential Issues in Vacant Properties:
Plumbing Systems
- Septic systems may initially function but fail under regular daily use
- Plumbing traps may show no signs of leaks during inspection but develop issues with active use
- Shower pans may only leak when subjected to the weight and movement of an occupant
- Seals for plumbing fixtures can dry out due to disuse, potentially leading to leaks when reactivated
Sewer Lines
- Root intrusion may allow water flow during testing but fail when processing waste and tissue, potentially causing backups over several days. A sewer inspection is always recommended.
Our Commitment
- We genuinely strive to conduct a thorough inspection by looking for indicators of past or existing problems. Our goal is to provide a realistic assessment of these systems' reliability based on the information available during the inspection. However, please understand that certain issues may only become apparent under regular use or over time. We recommend monitoring these systems closely upon occupancy and regular maintenance to ensure optimal performance and early detection of any potential issues.
Grounds
Drainage & Site Information
Clearance to Grade: Standard
Downspout Discharge: Above grade
Site Description: Flat
Several simple conditions and due diligence items were noted with the downspouts around the home - see list below. Repair these items as feasible to ensure proper moisture mitigation around the home.
Observations
- Extend the downspouts away from the home at many places - south side.
- A drain was noted below the west-side sunroom that did not appear robust enough to adequately manage moisture in this area. I observed evidence of water buildup (old debris) around the area, and the seller indicated that a puddle does form here. I recommend consulting a licensed drainage contractor for options to upgrade this drainage system.
- Dented and damaged gutter noted at the sunroom.
Driveways/Walkways/Flatwork
Driveway: Concrete
Walkways: Concrete
Typical cracking was noted in driveway flatwork. Several options for sealant are available at common hardware stores that you can get to match quite well. Seal the areas with an approved material to prevent water entry. Here is a link to more information on the subject: LINK.
Stairs & Railings
The exterior stairs were missing a graspable handrail for safety - see west side. Stairs with four or more risers need a handrail. Have a qualified contractor build suitable railings to reduce the potential for falls.
Grounds, Trees & Vegetation
Most Common: Arborist, Prune Vegetation
Trees were noted near the home and it is recommended to have a certified arborist conduct a comprehensive inspection of them. An ISA-certified arborist can evaluate tree health, identify any hidden issues like disease, decay, or weak branches, and provide maintenance recommendations tailored to your property. Regular professional evaluations help prevent property damage, especially if tree care hasn’t been performed in recent years. Pruning by a qualified arborist can also reduce wind stress, eliminate pest entry points, and support both safety and long-term property value.​
Recommendations
- Hire an ISA-certified arborist to evaluate tree health and safety, especially if pruning or removal may be needed.​
- Larger or overhanging trees may require pruning to reduce wind sail effect and minimize storm damage risks.​
- Regular inspections, ideally every 1–3 years, help detect issues early, including disease, dead limbs, and root problems.​
- Proper pruning discourages rodents and pests from accessing or nesting near your home.​
- DIY pruning is not always recommended as professionals have the experience, insurance, and tools to work safely near structures.​
Trees, shrubs or other vegetation were touching or growing close to the home. This is common and easy to fix with regular pruning and maintenance. Prune trees, branches and vegetation back at least six feet from the building, including any limbs over the roof. Trim them regularly as part of routine home maintenance to keep that space open.
Plants against the siding and roof hold moisture and block airflow and sunlight, so the exterior stays damp longer after rain. In our Pacific Northwest climate, that dampness makes the area a condition conducive to wood destroying organisms such as rot fungi, carpenter ants and other wood-boring insects. Branches touching or hanging over the roof also give rodents and other pests an easy path onto the roof and into attic vents or other small openings. Overhanging branches can also drop leaves and needles that clog gutters and wear down the roof.
Exteriors
Siding and Trim
Trim Material: Wood
Siding Material: Wood, Plywood
Most Common: Repairs, Deferred
The exterior siding materials showed multiple areas of deferred maintenance and localized damage – see list below. Hire a licensed contractor for a further evaluation and to come up with a cohesive plan for repairs and updating.
Observations
- Checked/damaged fascia board materials - several sides.
- Faded/peeling paint throughout the exterior.
- Staining at the eaves was faded and in need of re-application.
- Torn soffit screening - north side near chimney.
- Window trim needs paint – north side.
- Checked and sun damaged materials - south side at garage.
Eaves
Type: Enclosed system
Exterior Doors
Exterior Hose Bibs
Tested: Found to be functional where tested
Due Diligence: Update to Frost Free
This home featured older hose bibs at some locations, which could benefit from a thoughtful upgrade. Modern hose bibs—often called frost‑free or freeze‑proof faucets—are designed to protect against winter freeze damage. Instead of shutting off water right behind the handle, these fixtures place the shut‑off valve deeper inside the warm part of the wall. This design helps ensure that water drains out of the exposed section when turned off, reducing the risk of freezing, bursting and pipe repairs.
Today’s frost‑free models also typically include a vacuum breaker (an anti‑siphon feature) that prevents contaminated water from a hose from flowing back into the home’s water supply—a small detail with a big safety benefit.
I recommend upgrading to frost‑free hose bibs where feasible to make outdoor water access more reliable and easier to maintain year‑round, especially in our cold Northwest climate. For a quick visual demonstration of how a vacuum breaker works, check out this short video: LINK.
Most Common: Leaking
A hose bib leaked under pressure when tested. Hire a licensed plumbing contractor for repairs. This often requires tightening the packing around the handle stem and could be a straightforward repair.
Locations
- Rear side
Decks, Porches & Balconies
Decks, Porches & Balconies
General Information: Present - Info
For information about proper deck construction, that meets current requirements, see the PDF below,
WA Amendments 2020 IRC / Posts /Footings / Beams / Joists - LINK. If this deck is in Seismic zones D0, D1, D2 & D3 (most of Puget Sound) there are other requirements for construction that are better covered in this link: Deck Tip Sheet
Structure: Ground contact treated lumber
Ledger Attachment: Bolted - no flashing visible
Several conditions were noted with the deck installation - see the list below. Some of these items may not have been required under the building standards in place when the deck was originally built, but they remain worthwhile to retrofit now for improved safety and durability. I recommend having a licensed contractor further evaluate these conditions and perform all needed repairs.
Observations
- Missing flashing at the ledger board connections.
- Moisture damaged materials at the cantilever ledger board connection due to missing flashing.
- The deck is attached to a floor cantilever. This can be an unreliable connection as there is no wall below the rim joist for support. Consult with a qualified contractor about options for repair/improvement to ensure safe and reliable performance. Several options for strengthening this connection are using lateral load ties and building a post and beam system below the deck so it is self supporting and not reliant on the house connection.
- Moisture damaged support posts below sunroom - SW corner.
Fuel Storage & Distribution
Oil Storage
Due Diligence: Signs Found
There is evidence that this home was once heated with oil, as indicated by the old oil lines noted at the basement of the house. This likely means that a heating oil storage tank is present or was once buried on the property. These tanks were common in older homes and are not unusual to encounter today.
Recommendations
- Ask the seller for documentation showing that the tank was properly decommissioned or removed. In most cases, a fill valve is cut off once decommissioning is complete. If records are unavailable, consider hiring a tank‑locator service to verify whether a tank remains underground. This is a preventive step to help ensure there are no hidden environmental liabilities, as oil leaks from old tanks are much easier to address when discovered early.
- If a tank is found, have it evaluated and properly decommissioned or removed by a qualified contractor before closing.
More information
Roof, Chimney & Gutters
Roofing
Method of Roof Inspection: Walked on the roof
Roof Style: Gable
Roof Covering Materials:
- A single-ply membrane roof is a type of roofing system that uses a single layer of thermoplastic or synthetic rubber material to cover the roof. This type of roof is commonly used on commercial and industrial buildings, but it can also be found on some residential properties.
- A single-ply membrane roof does not typically require venting because the membrane material is designed to be airtight. This can be an advantage in certain situations, such as in buildings with HVAC systems that require a controlled indoor environment. However, proper insulation is still important to prevent heat loss and improve energy efficiency.
- To maintain a single-ply membrane roof without venting, it's important to regularly inspect the roof for any signs of damage or wear. Any areas of damage should be repaired promptly to prevent leaks or other issues. It's also important to keep the roof clean to prevent debris from accumulating and causing damage.
- Regular cleaning and maintenance can help prolong the life of a single-ply membrane roof. A professional roofing contractor can provide guidance on the specific maintenance needs of your roof based on its age, condition, and other factors.
Approximate Age of Roof Covering: The roof appeared to be installed around 2008, as evidenced by some of the printing on the flashing - consult with the seller for more accurate information
The roof appeared to be a 2008 or so installation but had a few items needing attention - see the list below. I recommend having a licensed roofing contractor further evaluate and complete these repairs to ensure reliable, long-term performance.
Observations
- Multiple areas of the roofing showed rippling and/or air trapped beneath the materials. While some minor rippling can be common, the extent noted here appeared excessive. This can result from improper installation (such as installation over an uneven deck or without proper acclimation), inadequate underlayment, or moisture beneath the shingles, and it may affect the roof’s appearance and long-term performance.
- Drainage appeared to be insufficient near the north chimney, where debris buildup was observed.
- Sealant at the solar tube was exposed and needed to be redone.
- The center chimney masonry showed wear and needed repairs.
- Organic debris buildup was noted at the roof covering. Due to the amount of nearby trees, diligent ongoing maintenance will be needed.
Chimneys
Chimneys: Present
Chimney Material: Masonry
Skylights & Sunroom
Type: Curb-mounted
The skylight design for the sunroom is an older style that requires diligent, ongoing maintenance. I observed portions of the caulking that had failed and are in need of maintenance at this time. I recommend consulting a licensed glazing specialist for repairs and updating where feasible.
Observations
- Multiple areas of moisture staining were noted below the top glass panels. This may indicate active leakage or a prior, since-resolved condition.
- A cracked window pane was noted. I recommend replacing it as needed to maintain a proper seal and prevent further cracking.
- Multiple failed seals were noted throughout the sunroom. Failed seals can allow air and moisture intrusion and often show as fogging or condensation between panes.
Roof Ventilation
Type: Soffit vents, Ridge vent
Gutters & Downspouts
Materials & Design: Metal
Limitations: Dry Conditions
Gutter systems need ongoing maintenance during each season. This typically includes cleaning the systems, maintaining sealant at the connections, and ensuring no active leakage is occurring. Because conditions during my inspection were dry, I cannot verify if any leaking connections are present, and all connections should be monitored and repaired as needed. Leakage may be noted during rainfall.
The gutters and downspouts needed common repairs/maintenance going forward - see list below. Implement repairs to ensure they are clear of obstructions, well fastened, leak free and sloped to drain.
Observations
- Multiple portions of the gutters were full of organic debris.
- Loose gutters noted that needed to be secured.
Roof Limitations & Exclusions
Roof Inspection Limitations / Exclusions: Information, Dry
This report provides a general assessment of the roof system's condition based on a visual inspection of accessible and representative areas. It is important to note that this inspection does not guarantee the absence of leaks or predict future leakage. The inspector’s observations are limited to the conditions visible at the time of inspection. For a more detailed analysis or corrective measures, consultation with appropriate specialists is advised.
Limitations of Inspection
- Roof inspections are inherently limited by factors such as weather conditions, accessibility, and the design of the roof system. For example, if the inspection occurs during dry weather or outside the rainy season, potential leaks may not be evident. Water stains on ceilings, walls, or soffits that appear dry during inspection may retain moisture under different conditions or at later times.
Potential Risks
- Specific observations regarding leakage or stains do not rule out the possibility of additional hidden damage or undetected areas of concern. It is recommended to monitor attic spaces for changes over time. If any ongoing issues or questionable conditions arise, they should be promptly evaluated and addressed by a qualified professional. Note that prolonged leakage can result in mold, fungal growth, or other moisture-related damage.
Attic Inspection Limitations
- Due to common design and accessibility constraints—such as insulation, storage items, or structural obstructions—attic evaluations are typically limited in scope. Any limitations or obstructions noted in this report are intended to flag areas that fall outside the standard scope of inspection. A thorough evaluation of the attic should be conducted once temporary limitations are resolved.
Installation Limitations
- Verifying nailing patterns or fastener installation is not possible on roofs that are fully bonded, as doing so would require breaking the adhesive seal. This type of destructive inspection is beyond the scope of a standard home inspection.
Roof Limitation:
My inspection of the roof was performed during an extended dry period with no recent rainfall. As a result, active leaks or moisture intrusion may not be visible at this time — hidden or intermittent leaks might only become apparent during or shortly after heavy rain.
Garage
Garage General
Garage Type: Attached
Microbial-like staining patterns were noted on the wall of the garage. These are likely from a prior moisture condition. Testing at the time indicated the wall was dry. I recommend using a stain killing primer and paint to seal this stain.
To improve fire safety between the garage and the house, a minimum of 1/2 inch gypsum board (sheetrock) is needed on the garage side of walls that separate the garage from living spaces. This fire separation is specifically designed to slow the spread of fire from the garage to the rest of the home, significantly increasing occupant safety. In contrast, older homes with wood walls in the garage do not meet current fire safety standards and are not considered compliant with modern code requirements.
Garage Doors & Automatic Openers
Overhead Garage Door Type: Tilt Up
Automatic Garage Opener: None noted
Garage Occupant Door: Solid Wood
The installed garage door was an older tilt-up (one-piece swing) design, which is generally less reliable and convenient than newer sectional models. This style swings outward as it opens, so a vehicle or objects must be parked far enough back to allow the door to open fully. These older doors also typically lack the safety features of modern openers, such as auto-reverse and photo-eye sensors. I recommend considering an upgrade to a newer sectional door and opener with current safety features, as desired.
Electric Service
Electric Service Permits Found
Permits: None Found
No permit stickers or paperwork related to electrical work were found on the electric panel. Inquire with the seller for any additional information about this installation.
Electric Service Voltage Tested
Service Voltage: 120-240 Volts
Testing Note: Testing Note
I tested the voltage at the electric panel at a normal range of 235-245 volts. Most residential construction is listed as 120/240 volts and it is normal for some slight fluctuation.
Electric Service
Service Entrance: Above Ground
The property was served by an overhead electrical service. All trees and branches near electrical lines should be diligently trimmed and maintained to prevent contact with the wires. Overgrown vegetation can lead to physical damage to the service conductors, create shock or fire hazards, and cause service interruptions during storms or high winds.
Trimming around electrical lines should always be performed by a qualified arborist or licensed electrical contractor familiar with safe clearance requirements. Regular maintenance will help ensure safe and reliable electrical service to the home.
Meter Base Amperage: 200
The service neutral connection appeared to lack the barrel clamp (connector) typically present at this location. Because this connection is at the utility service entrance, I recommend consulting your local utility provider for further evaluation to confirm the connection is adequately rated and properly secured.
Circuit Breaker Identification
Information: Recommendation
For safety the homeowner should always see to it that the circuits in the panel are properly labeled. This can be done when the electrician is at the home for other reasons, but accurately identifying circuits can assist in shutting down circuits quickly when they need to be.
When safe to do so, I visually inspect the interior components of the electrical panels serving the home, looking at the type and condition of the wiring and checking for signs of failure or improper installation. Some components fall outside the scope of this inspection, such as surge protection and generator wiring installations. While I note the size of the electrical service, I cannot predict whether it will be adequate for a homeowner's needs. All electrical work should be performed by qualified, licensed professionals.
Service Equipment
Service Entrance (SE) conductor Size: Copper, 2/0, 200 amps
Amperage: 200 amps
Electric Service Amperage: 200 amps
Service Equipment Location: Garage
Panel Manufacturer: Cutler Hammer
Multiple double-lugged neutrals were noted at the busbar - this is where two conductors are terminated under a single lug. Neutral (grounded) conductors in particular should each land on their own individual terminal, because a shared neutral lug can loosen, overheat, and create an unreliable or unsafe connection. It can also make it unsafe to service a single circuit, since loosening the lug affects more than one conductor. I recommend repair by a licensed electrical contractor so each neutral is terminated on its own terminal.
- Code Reference: The National Electrical Code (Article 408.41) requires each grounded (neutral) conductor to terminate at an individual terminal not shared with another conductor. Washington adopts the NEC as part of its electrical code.
Electrical Grounding System
Limitations: Cannot Confirm Effectiveness
During my visual inspection, I make every effort to thoroughly examine the visible components of the electrical grounding system. This system plays a crucial role in safely discharging electrical surges, particularly during lightning strikes. I aim to provide the most accurate information possible within the scope of a standard home inspection. However, a definitive assessment of the grounding system's effectiveness may require specialized testing beyond this inspection's scope.
Limitations of Inspection
- Many components of the grounding system are not visible.
- Standard home inspection procedures do not include practical tests to verify the system's effectiveness.
- Unlike a furnace or plumbing fixture, there is no simple method to test grounding system performance.
My Approach
- I focus on identifying potential issues or irregularities that may indicate problems with the grounding system. Any concerning elements observed are documented in the observations section below.
Professional Evaluation
- Where I identify potential issues or have concerns about the grounding system, I may recommend further evaluation by a licensed electrical contractor for a more comprehensive assessment of the system's integrity and functionality.
Electrical Bonding System
Limitations: Cannot Confirm Effectiveness
During my inspection, I conduct a visual assessment of the electrical bonding system. This critical aspect of electrical safety requires all metallic systems within the building to be connected to the electrical grounding system. My goal is to provide a comprehensive understanding of your property's electrical bonding system within the scope of a standard home inspection. However, a definitive assessment of the system's effectiveness may require specialized testing beyond this inspection's scope.
Purpose of Bonding
- Creates a pathway to dissipate static charges that might otherwise accumulate on the system.
- Provides a safety mechanism to trip a circuit breaker if bonded metallic components become energized.
Limitations of Inspection
- Standard home inspection procedures cannot definitively verify the effectiveness of system bonding.
- Some bonding connections may not be visible or accessible during the inspection, which is typical.
My Approach
- I focus on identifying visible indicators of proper bonding and potential issues that may compromise the system's integrity, providing a general assessment based on observable elements.
Professional Evaluation
- If I identify any concerns with the bonding system, I may recommend further evaluation by a licensed electrical contractor. Such recommendations, if necessary, will be documented in the observations section below.
Electric Distribution & Finish Wiring
Branch Wiring
Wire Material: Copper, Multi-strand Copper
Most of the electrical wiring in this home was concealed within walls, floors, and ceilings and was not directly visible for inspection. As a result, the inspection was limited to the exposed and readily accessible portions of the electrical system only; the condition of concealed wiring, junctions, and splices could not be determined and is beyond the scope of this inspection.
Wiring Method: Non-metallic sheathed cable, Early Romex
The home’s electrical system, typical of pre-1962 construction, featured original ungrounded wiring. This type was commonly used in homes built before the 1960s and consists of two insulated conductors (hot and neutral) encased in a non-metallic sheath - often cloth or rubber, with some variations including additional paper insulation. While this was standard and acceptable at the time, it does not include a dedicated grounding conductor, which is now a standard safety feature in modern electrical systems.
Although ungrounded Romex-style wiring was an improvement over older systems like knob-and-tube, it does present some safety considerations. Without a grounding conductor, there is no dedicated path to safely carry a fault to ground, which can pose a shock or fire risk. In addition, many modern appliances and electronics are designed for grounded receptacles, and using them on ungrounded wiring can lead to improper operation or potential damage to the devices.
While this type of wiring is not uncommon in older homes, it’s something to be aware of. I recommend consulting a licensed electrician to discuss potential upgrades and improvements for added safety and compatibility with today’s standards - such as GFCI protection for ungrounded circuits, whole-house surge protection, and AFCI breakers.
Observations
- Multiple ungrounded receptacles were still in use - garage.
- Original cloth wiring noted above the electrical panel.
- Grounded receptacles were used on ungrounded wiring throughout the home.
Wiring, Receptacles & Fixtures
Inspection Method: Random Testing
Receptacles: Three wire receptacles
GFCI: GFCI - Testing Procedure Note
During inspection, I test all Ground Fault Circuit Interrupter (GFCI) devices that are readily accessible. GFCIs are receptacles with reset buttons commonly found in bathrooms, kitchens, and at the exterior of the home. GFCIs are important safety devices that limit the duration of electrical shocks and have demonstrably saved lives. I recommend being aware of where reset buttons are located in the house, as GFCIs can trip and disable a circuit that cannot be re-energized without resetting the button. I avoid testing to determine whether a receptacle or circuit is GFCI-protected if it's unclear where the reset button is located, since reset buttons can be concealed behind stored items — such a test risks disabling a circuit in the home. Occasionally, a GFCI can fail during testing; this is a statistical reality, and some devices will require replacement as a result.
Testing of ground-fault circuit-interrupter (GFCI) devices is limited to operation of accessible test buttons and use of a simple plug-in tester at readily accessible receptacles; inspection does not include moving occupant belongings or appliances, dismantling equipment, verifying wiring configuration at each protected receptacle, or confirming manufacturer-recommended test intervals.
Testing Information
Ground fault circuit interrupters (GFCI) can help prevent electrocution inside and outside the home. GFCIs are an effective means of protecting against electrical shock, however, they must be tested regularly -- UL recommends once a month -- to verify they are working properly.
- Plug a nightlight (with an "ON/OFF" switch) or other product (such as a lamp or 3-bulb circuit tester) into the GFCI receptacle and turn the product "ON."
- Push the "Test" button located on the GFCI receptacle. The nightlight (or other product) or circuit should go "OFF."
- Push the "Reset" button. The light or circuit should go "ON" again.
- Circuit breaker type GFCI devices are checked by pushing the test button on the breaker.
- Modern GFCI receptacles and breakers have "self-testing" capabilities but they still should be tested manually per manufacturer's instructions.
Several conditions were noted in the home's wiring system - see the list below. I recommend evaluation and repair by a licensed electrical contractor as needed. Please note that electrical systems are largely concealed within walls, ceilings, and other finished areas, so additional latent or hidden defects may exist that were not visible during this inspection.
Observations
- Missing an exterior rated cover plate - west side under deck.
- A GFCI receptacle did not have power and would not reset - SE corner.
- Two light fixtures in the kitchen did not function.
- Exposed wiring - hallway closet ceiling.
- Missing GFCI protection near the basement sink.
Ceiling Fans
Ceiling Fans: None Noted
Low Voltage Wiring
Information: Limitations
Low‑voltage wiring and related systems are outside the scope of this home inspection. This includes timers, sensors, security and alarm systems, data/TV/cable wiring, doorbells, intercoms, low‑voltage lighting, surge or lightning protection, and similar auxiliary equipment. Evaluation of these components is not performed unless specifically noted otherwise. No determination is made as to whether electrical devices or fixtures are properly UL‑listed; some imported fixtures may not carry a UL mark.
Plumbing
Water Meter
Meter Location: Location Noted
This shows the location of the water meter at the street side of the house.
Water Service Supply
Pipe Material: Copper
Water Supply: Public water
Water Pressure: Tested (Normal Range - Photo)
Water pressure can fluctuate throughout the home from location to location for multiple reasons. I do my best to determine if the functional flow of water in the home is adequate and this can also change depending on the occupants needs. Typical water pressure for a home will be between 30-65 PSI, and is acceptable up to 80 PSI. Unless noted in the report below, the water pressure observed at the fixtures appeared to be acceptable. Water pressures in excess of 80 PSI risk damaging supply piping components and should be controlled with a pressure reducing valve.
Pressure Reducing Valve: None noted
Main Water Shut-off Location: Water Shut Off Location Noted
This shows the location of the main water shut off located in the basement. These valves should be periodically cycled through to ensure proper operation - if left unused they can freeze in a single position.
Distribution Pipe
Supply Pipe Materials: PEX, Only Partly Visible
Portions of the water supply piping in this home were concealed behind insulation as well as wall and ceiling finishes, making a complete visual inspection impossible within the standard scope of a home inspection. As such, identification of piping materials is based on an informed visual assessment of the accessible sections found at plumbing fixtures and exposed areas (below sinks and so on). Please note that hidden piping may differ from those observed, and conditions or materials that are not visible cannot be evaluated.
Pipe Insulation: Missing at some areas
Functional Flow: Good
Circulation Pump: None Noted
Angle Stop Limitation: Testing Note
Angle stops are the small shut-off valves located below plumbing fixtures such as sinks and toilets. They allow water to be shut off locally to a single fixture, without shutting off water to the entire house, so that fixture can be serviced, repaired, or replaced. As a homeowner, it's worth knowing where these are, since they let you quickly stop a leak at one fixture in an emergency.
Please note that home inspectors do not operate angle stops during an inspection. These valves are often old or rarely used, and turning one can cause it to seize or leak — sometimes failing to fully shut off or reseal afterward. Because operating them carries a real risk of causing a leak, they are left undisturbed and their function is not verified as part of this inspection.
The supply pipe insulation was incomplete in the garage at many areas. Be sure all supply lines in unheated spaces have been adequately insulated to protect from freezing conditions that could damage the pipes and to prevent heat loss.
Waste Pipe & Discharge
Discharge Type: Public Sewer - Sewer Scope Performed
Please note that the sewage discharge type listed here is based on public records and seller disclosure. It is always possible that the actual system differs from what is reported. For example, a property could be listed as connected to public sewer when it is in fact served by a private septic system. While this is unlikely, it's one more reason I recommend independent evaluation of the sewage discharge system to confirm its type and condition.
- A sewer scope was performed at the time of this inspection - please see the relevant section of the report for detailed findings.
Water Heater
Water Heater
Manufacturer: Bradford White
Data Plate: Shown Here
This shows the data plate for this water heater.
System Type: Standing Tank
A single-family storage water heater offers a ready reservoir -- from 20 to 80 gallons -- of hot water. It operates by releasing hot water from the top of the tank when you turn on the hot water tap. To replace that hot water, cold water enters the bottom of the tank through the dip tube where it is heated, ensuring that the tank is always full. Conventional storage water heater fuel sources include natural gas, propane, fuel oil, and electricity. Please follow this link for more information - LINK
Size: 50 gallons
Age: 2022
Energy Source: Electricity
Seismic Straps: Present
Pad: Present
Expansion Tank: Present
Temperature Pressure Relief Valve: TPRV Notes (Present - Not Tested)
A temperature and pressure relief valve (TPRV) is a critical safety device required on all water heaters. It automatically releases water if the tank's temperature or pressure climbs too high, preventing a dangerous buildup, which is why it must have a drain line directing any discharge to a safe location away from people, typically the exterior or an approved drain.
Most manufacturers recommend testing the valve annually by briefly lifting the lever, with professional inspection about every three years. I do not operate TPRVs during an inspection, as they can fail to reseat and leak once disturbed. A TPRV that leaks or won't release should be replaced promptly by a licensed plumber.
One note on the drain line: codes, water-heater instructions, and manufacturer requirements sometimes conflict on specifics like pipe type, size, and termination height, so a "perfectly correct" install isn't always possible. I prioritize the manufacturer's instructions, including terminating the drain about 6 inches above the floor where feasible.
General Maintenance: Standing
Water heaters generally last 8 to 12 years, but with regular maintenance you can extend both their lifespan and efficiency. This work can be handled by a licensed plumbing contractor or a knowledgeable homeowner. Here's a quick guide to essential water heater maintenance:
Annually flush the tank to clear out sediment buildup:
- Turn off the power (electric) or gas supply (gas)
- Attach a garden hose to the drain valve and empty the tank
- Refill the tank, then restore power or gas
Inspect the anode rod — the sacrificial metal rod that protects the tank from rust:
- Check for significant corrosion or calcium buildup
- Replace it if it's less than ½ inch thick or heavily coated
For gas water heaters, also:
- Clean the burner and combustion chamber
- Check the venting system for blockages or damage
Every 3 to 5 Years
- Replace the anode rod if it's more than 50% depleted
- Inspect and upgrade the insulation on both the heater and its connected pipes to improve energy efficiency
Water Temperature
Water Temperature Information: Info
Having plenty of hot water is not just a convenience, it is considered a necessity in modern homes. However, there are competing concerns related to having plenty of hot water. On the one hand we want to prevent scalding. On the other hand it is a good idea to keep water hot enough to prevent water-borne bacteria from flourishing. It is actually quite complicated to accomplish both goals with storage-tank type water heaters.
- This is further complicated by Washington State Home Inspector Standards of practice that require us to report when the tested water temperature is above 120 degrees Fahrenheit (including a statement that the generally accepted safe temperature is 120 degrees Fahrenheit). Another complication is that some dishwashers do not have integral water heaters and prefer much hotter water coming to it from the primary water heater.
- This information, however, only addresses one of the safety concerns–and can actually make the other concern worse. Temperature below 120 degrees Fahrenheit is considered ideal for the growth of harmful bacteria inside the tank–such as Legionella. Keeping the tank temperature between 135 and 140 degrees Fahrenheit can greatly reduce the risk of growing bacteria in the tank but is not a guarantee. For example, Legionella bacteria can survive extreme hot water and chemical treatment by forming a parasitic relationship with amoebae that are not affected by these treatments. While rare, it is still considered prudent, given the current state of knowledge, to maintain the tank water temperature between 135 and 140 degrees Fahrenheit to at least provide some degree of protection.
- While "generally-healthy-people" are fairly resistant to infection, some patient populations (organ transplants, diabetes, cancers, kidney disease etc), immunocompromised persons, heavy smokers, heavy drinkers, the elderly and infants can be expected to have higher death rates or incidence of more severe illness if the bacteria is present in sufficient numbers. Some authorities assert that an increase in incidence can be expected with an increased focus on conserving energy (lowering the thermostat on the water heater). The science around all of this is ongoing and new information should be anticipated.
But what about scalding?
Preventing scalding requires a multifaceted approach.
We must resort to good sense:
- Never leave a child or infant alone while drawing water in a bathtub, and check the water temperature before putting your child or the infirm in the tub.
- Test the water temperature before bathing or showering.
- Turn the cold water on first, then add hot water until the temperature is comfortable.
- Teach children to turn the cold water on first, and the hot water off first.
Provide a mechanical means (Thermostatic mixing valve) of lowering the temperature to below 120 degrees Fahrenheit at either the points of use or at the water heater itself to protect the whole house. Because these devices can fail, we must always keep #1 in mind.
For additional information on this issue please check out the links below:
Thermostatic mixing valves:
- Thermostatic mixing valves located at the water heater are designed to reduce hot water temperatures in the tank to levels considered safe at points of use (sinks tubs etc). They can be adjusted and should be periodically checked to verify function. These valves are desirable so that tank temperatures can be maintained high enough to limit bacteria growth inside the water heater while at the same time providing water at a safe temperature where desired.
Water Temperature Measured During Inspection: Too Cold
The water heater temperature was set too low at the time of inspection - just 107 degrees F. About 120 degrees F at the fixtures is the generally recommended temperature, so I recommend adjusting the water heater setting as needed. For best practice, many plumbers set the tank to 130-140 degrees F and install a tempering (mixing) valve so water is delivered to the fixtures at a safe 120 degrees F. The higher tank temperature helps reduce the risk of Legionella bacteria developing in the tank.
Laundry & Additional Plumbing
Washers
Information: Tested
The washing machine was briefly operated through a normal cycle and appeared functional at the time of inspection. No leaks or obvious defects were observed. Please note that this test is limited to general operation and drainage; it does not evaluate cleaning effectiveness or internal mechanical performance, which are beyond the scope of a home inspection. This check was provided as a courtesy beyond the standard inspection requirements. Performance after the date of inspection cannot be guaranteed.
Consider the following homeowner care practices going forward:
Regular Cleaning
- Clean the detergent drawer periodically with warm soapy water to prevent buildup.
- Every few months, run a hot cycle with vinegar or a washing machine cleaner to remove residue and control odor.
Inspection and Replacement
- Inspect supply hoses regularly for cracks or bulging and replace them if damaged.
- Consider upgrading to braided stainless-steel hoses for improved safety.
Proper Usage
- Keep the washer level to minimize vibration and wear.
- Follow manufacturer guidelines for load size to avoid undue strain on the motor and suspension.
Professional Service
- Have the appliance professionally serviced every one to two years for internal inspection and maintenance.
Most Common: Older Units, Update Hoses
The clothes washer and dryer appeared to be older units. Both were operating at the time of inspection; however, due to their age and visible appearance, upgrading these appliances at your convenience may be worth considering.
Water Supply Connectors
- Replace existing hoses with stainless steel-braided ones
- Install flood-stop devices for leak prevention
- Replace hoses every 3-5 years, even if they appear intact
Drain Piping
- Secure the drain pipe to prevent movement during use
- Fasten it to nearby water pipes or wall studs
- Use appropriate clamps or brackets for a stable connection
Dryers
Information: Tested
The dryer was briefly operated and appeared functional at the time of inspection - no obvious defects were observed. Please note that this test is limited to general operation; it does not evaluate drying effectiveness or internal mechanical performance, which are beyond the scope of a home inspection. This check was provided as a courtesy beyond the standard inspection requirements. Performance after the date of inspection cannot be guaranteed.
Dryer Exhaust Duct Safety & Best Practices:
General Requirements:
- Dryer exhaust ducts must be independent of all other systems, convey moisture directly outdoors, and terminate outside the building according to the manufacturer’s installation instructions. A backdraft damper is recommended at the termination.
Duct Material & Construction:
- From the laundry room wall to the exterior, exhaust ducts should be constructed of rigid metal with smooth interior surfaces. Joints should run in the direction of airflow—never use sheet-metal screws or fasteners that protrude more than 1/8" into the duct, as these can trap lint. Do not install screens at the duct termination.
Lint Filter Maintenance:
- Every dryer should have a clean lint filter. Clean the filter between every use to prevent fire hazards and maintain efficiency. Fabric softeners (sheets or liquids) can clog filters and reduce airflow, even when they appear clean; consider using natural alternatives.
Transition Duct (Connector):
- The short duct between the dryer and the wall duct is called the transition duct or connector. It must be UL-2158A listed and constructed of smooth metal, corrugated metal, or a specific UL-2158A listed foil type. Most standard foil connectors do not meet requirements and perform poorly under heat; they are not recommended. Annual professional cleaning is recommended.
Best Practice:
- Only use rigid or corrugated metal transition ducts. However, the DryerFlex™ type of UL-2158A listed foil connector is an exception—it performs better under extreme heat than traditional metal options and is highly recommended. Note: DryerFlex™ is typically available through duct cleaning professionals or online, not at big-box stores.
Fire Safety:
- Dryers are a leading cause of household fires. The National Fire Protection Association (NFPA) recommends only rigid or corrugated metal transition ducts be used. NFPA Dryer Safety Tips.
Power Source: Electric
The dryer vent for the garage laundry area did not terminate to the exterior as it should. Dryer exhaust vented into the garage (rather than outside) releases significant moisture and lint into the space, which can raise humidity and create a fire hazard from lint accumulation. I recommend having the dryer vent properly routed and terminated to the exterior by a qualified contractor.
Laundry Sinks & Countertop
Sink: Tested
HVAC & Ventilation
Heating & Cooling Systems
System Performance: Information
Everyone wants to be comfortable in their home. How well a building heats depends on a host of factors, many of which are difficult to control or improve:
- Older homes are typically the hardest to heat evenly, while newer homes carry a higher expectation of good performance. There are all manner of rules of thumb floating around online, but these are usually only accurate under very specific conditions. A truer picture requires knowing the building's volume, its air infiltration and exfiltration rates, and how thermally efficient the walls, ceilings, floors, doors, and windows are — as well as whether the home sits on a slab, over a crawl space, or over a basement.
- The efficiency of the heating and cooling systems themselves also matters: how efficiently the equipment runs, whether the ductwork is leaky, and whether that ductwork runs through unconditioned space (such as an attic or crawl space), where it loses more energy.
- For a comprehensive assessment and tailored recommendations, consulting a Building Performance Professional can be invaluable. They can pinpoint areas for improvement and suggest practical improvements — for instance, sealing ductwork often makes a bigger difference in comfort and efficiency than replacing old windows.
Energy Source: Electricity
Heating & Cooling Method(s): Electric wall heaters, Heat pump
Electric wall heaters consist of a heating element with a reflector behind it that directs heat into the room, typically paired with a fan to circulate warm air. They are most often installed on interior walls, since mounting them on exterior walls makes proper insulation in that wall cavity difficult to achieve.
These units are generally low-maintenance but should be kept clean and free of dust buildup on the element and fan to operate safely and efficiently. Furniture, curtains, and other combustibles should be kept clear of the heater face to reduce fire risk.
One very important point to understand when answering the question “how do heat pumps work?” is that heat pumps do not generate heat – they move heat from one place to another. A furnace creates heat that is distributed throughout a home, but a heat pump absorbs heat energy from the outside air (even in cold temperatures) and transfers it to the indoor air. When in cooling mode a heat pump and an air conditioner are functionally identical, absorbing heat from the indoor air and releasing it through the outdoor unit. Click here for more information about heat pumps vs air conditioners.
Service Records & Data Plate: Service Records and Data Plate
These photos show the most recent service records on the HVAC system(s) as well as the listing plates where available.
Age: 2019
Records for the heating/cooling system indicated it was serviced within the past year; consult the seller for documentation to confirm this to your satisfaction. The manufacturer recommends annual servicing, and I advise continuing with a yearly maintenance schedule by a licensed HVAC contractor, including inspection of the heat exchanger.
The electric wall heaters were an older design, and upgrading to modern units is worth considering - see sunroom. Newer units offer improved efficiency and safety compared to the currently installed heaters. Consult with an HVAC contractor and/or licensed electrician for further information and upgrade options.
Air Filters
Filtration Systems: Disposable
Your system has disposable air filter(s) installed. These should be changed quarterly or more to ensure proper air flow at the furnace. Be sure to install the filters with the arrows pointing in the same direction as the air flow. Here is a link to more information regarding air filtration - LINK.
Heating & Cooling Distribution Systems
Heat Source in Each Room: Present
Testing Notes: Thermal Images
Thermal images showing approximate temperatures when testing the heating and cooling systems. I use these images just to show the system was generally functioning during inspection. These are representative photos and do not indicate how well the systems are functioning.
Mechanical Ventilation Systems
Type Of System: Upgrade Ventilation
The installation of a mechanical ventilation system would be a logical upgrade for this home. As the home predates the requirement for this, there are several options, including a whole house fan on a timer exhausting air to the exterior and bringing in fresh air, a heat recovery ventilator (HRV) and so on. Consult with a licensed HVAC contractor about improvements to the home's ventilation design.
Information
Solid Fuel Fireplaces
Fireplace Types: Masonry firebox
The wood burning fireplace has a flue damper inside. This is designed to keep cold air out of the house when the fireplace is not in use. Be sure to keep the flue damper closed during the heating season when the fireplace is not in use to prevent heat loss.
A wood burning fireplace and wood stove were noted in the home. The NFPA (National Fire Protection Association) recommends an annual inspection of all chimneys, fireplaces, solid fuel-burning appliances, and vents. They also recommend an NFPA 211 Standard, Level II inspection upon sale or transfer of the property. A Level II inspection includes, not only cleaning the interior of the chimney pipe, but also the use of specialized tools and testing procedures such as video cameras, etc. to thoroughly evaluate the serviceability of the entire flue lining and fireplace/chimney system. If a chimney cleaning has not been performed over the past 12 months, such an inspection is recommended before closing and prior to first use for fire safety reasons - consult with a CSIA-certified chimney sweep for this inspection service. Implement any repairs as recommended.
Upgrades
- For improved energy efficiency, install glass doors for the front of the fireplace to reduce heat loss during winter months. Be sure to keep the flue damper inside the firebox closed as well. Chimneys are very good at sucking heat out of your house and glass doors and flue dampers help to slow this heat loss.
Interior
General Information
Observations: Limitations
Personal belongings, furniture, and stored items were present throughout the property at the time of inspection. These items can conceal damage to walls, floors, ceilings, and other surfaces, as well as obscure access to systems and components that would otherwise be evaluated. Concealed defects are not within the scope of this home inspection and cannot be reported on if they were not visible or accessible. Some conditions may only become apparent during the course of moving, remodeling, or other more invasive investigations. Every reasonable effort was made to move lighter items and inspect around or over stored belongings to provide the most thorough evaluation possible under the circumstances. I recommend a walk-through of the property once it has been emptied, prior to closing, to identify any previously concealed conditions.
INTERIORS LIMITATIONS:
- No comments are offered on cosmetic finishes.
- Area rugs
- Furnishings
- Built-in cabinets
- Appliances
- Storage items
- Curtains/blinds
- Bookcases
- Paintings/pictures
- Mirrors
- Storage below several sinks
- Storage items in the closets
Floors and Floor Materials
Floor Materials: Hardwood, Tile
Most Common: Refinish Hardwood
The hardwood floors were scratched and the finishes were wearing in some areas. Hire a wood floor specialist to evaluate and refinish the floors to your satisfaction.
Information
- Options typically include: a complete sand and finish which, if there is enough material on the wood, can make the floors look new - or a simpler option of just adding more finish and leaving many of the scratches and dings.
Walls, Ceilings, Trim and Closets
Wall & Ceiling Materials: Drywall
Water stains were noted on the ceiling near the chimney. These stains were tested with a moisture meter during the inspection and read dry at that time, which suggests the source may be from a prior, since-resolved condition rather than an active leak. I recommend asking the seller about any history of leakage in this area to better determine whether repairs are needed to prevent a recurrence. Once any source is confirmed resolved, the damaged sheetrock can be repaired and painted as needed for a proper cosmetic finish.
Wall Insulation and Air Bypass
Wall Insulation: Not Visible
Stairs and Railings
Stair Findings: Non-standard
Most Common: Riser Height
The interior entry stairs had non-standard riser heights - see short first step. The tallest riser should not exceed the smallest by more than 3/8ths of an inch. Have this further investigated by a licensed contractor and repaired as feasible; this can be tricky to repair sometimes.
- Please follow this link to current code information - LINK.
Interior Doors
Limitations & Testing Procedures: Tested
Several doors were tested throughout the home and were found to be functional. Exceptions will be noted below.
The "Security" of any home is never absolute. At the time of inspection I assess the "basic functionality" of door and window locking mechanisms. No assessment of the individual or overall effectiveness of security is implied. Glass, frames, locks and other elements can be prone to "tampering" and are "limiting factors" of locking mechanisms/systems. All security devices and systems must be balanced against the ease of escape in the event of emergency. Concerns about the home's overall security system should be addressed by a licensed home security company.
Most Common: Adjust
Doors throughout the home were in need of adjustment and general maintenance - see the list below. These are typically minor items, and I recommend having a handyperson adjust and repair the doors as needed.
Observations
- Missing doorstops at multiple closet doors.
- The north bedroom closet door and entry door rubbed on their frames.
- The closet door in the NE bedroom was missing a panel and the track was damaged.
- The primary bathroom door rubbed on its frame.
- Damaged door - NE bedroom.
- The basement NE bedroom door did not latch.
Windows
Limitations & Testing Procedures: Testing Procedures Note
During the inspection, I operate (open and close, lock, and so on) a representative number of windows in the dwelling. I do my best to test all windows for functionality, but that isn't always possible due to stored items (couches, decorations, and so on) blocking access. I also look closely for lost seals in the glazing. Lost seals aren't always easy to spot and can become more apparent with changes in humidity and temperature at any point during ownership.
Problems with double-pane windows are common: sash issues, condensation issues, broken hinge mechanisms, broken or missing latches, corrosion, broken thermal seals, defective thermal coatings, failed paint, failed glazing, and so on.

While I attempt to identify as many window defects as possible, not all windows can be tested and some may be obstructed from view (by screens, blinds, vegetation, etc.). This means some issues may go undetected. Most individual window issues are typically not considered "deal breakers" for a home purchase, so the inspection generally focuses on more substantive concerns. Windows are locked after testing when possible.
Window coverings and blinds are not inspected for function at the time of inspection except as part of testing the windows themselves. I recommend testing these blinds as desired.
Drawstrings and slatted-type coverings can pose a strangulation hazard for small children. I recommend considering newer, safer blind designs. For more information on window blind safety, see the Consumer Product Safety Commission's guidance.
- Move all cribs, beds, furniture, and toys away from windows and window cords, preferably to another wall.
- Keep window cords out of the reach of children. Tasseled pull cords should be short, and continuous-loop cords should be permanently anchored to the floor or wall.
- To prevent inner-cord hazards, lock cords into position when lowering horizontal coverings or shades.
- Repair window coverings, corded shades, and draperies manufactured before 2001 with retrofit cord-repair devices, or replace them with today's safer products.
- Consider installing cordless window coverings in children's bedrooms and play areas.
Window Glazing: Double pane, Single pane
Interior Window Frame: Metal, Metal - Older
A failed window seal was noted in the glazing at 1-2 windows, and more may become apparent as exterior conditions change. The symptoms often take the form of condensation between the panes of glass and these failures are more a cosmetic consideration than a functional one. The failure does not significantly affect the thermal insulation value of the window, however, the fog cannot be removed by normal cleaning. There is no simple fix for this condition, short of replacing the entire glazing unit. Not all windows may be represented in the photos. I recommend evaluation and replacement of any failed windows as desired. Please follow this link for more information - LINK.
Locations
- Lost seal - basement NW family room.
Some windows in this home are older single-pane units with metal frames. These do not meet modern standards for safety glazing or thermal performance, which is common and expected in windows of this age. Metal frames also conduct heat and cold readily, so these windows tend to be less energy-efficient and more prone to condensation than modern assemblies.
Upgrading is optional rather than required - but improvements in comfort, energy efficiency, and safety may make it worthwhile. Full replacement with modern dual-pane units offers the greatest benefit, while a simpler alternative is to apply protective safety film to the existing glass to improve its impact resistance. I recommend consulting a qualified glazing or window contractor to review the existing windows and provide evaluation and upgrade options appropriate for the home.
Windows - Older
Due Diligence: Egress - Older Standard
The bedrooms in this home had escape and rescue openings that do not meet current standards. This is very common in older homes, as these requirements were not in place when the home was built, so it is considered a worthwhile safety upgrade rather than a defect. Current standards call for bedrooms to have a second means of escape in an emergency - typically a window, though a door can also satisfy this. Upgrading these openings would improve occupant safety, particularly for use as an emergency exit or for firefighter access. I recommend having a licensed general contractor evaluate the openings and update them where feasible.
Egress window - basic requirements:
- 20" minimum width
- 24" minimum height
- 5.7 sq. ft. net clear opening (5.0 sq. ft. at grade level)
- Sill no more than 44" above the floor
- Opens easily without keys or tools
Window well (if below grade):
- 9 sq. ft. minimum area
- 36" minimum projection and width
- If deeper than 44": a permanently affixed ladder or steps, usable with the window fully open
Smoke & Carbon Monoxide Alarm Systems
CO Alarms Noted: Installed where currently required
CO Alarms: Present
At the time of inspection Carbon Monoxide alarm/detectors are not tested. I recommend that prior to move-in, that all Carbon Monoxide alarm/detectors be tested and have their batteries replaced. It is recommended that Carbon Monoxide detectors that are older than 10 years should be replaced by a licensed electrical contractor if they are hard-wired; and replaced by the building owner/handy-person if they are battery operated. These devices are currently required, according to Washington State Law to be maintained by the tenant/homeowner according to the manufacturer's recommendations/instructions and are required in all homes.
- For optimum safety, Carbon Monoxide alarm/detectors are required in the immediate vicinity of bedrooms and on each floor level of the home and inside of any sleeping room if there is a gas appliance in the room. "Immediate vicinity" is not defined but most manufacturers recommend they be installed between 5 and 20 feet of sleeping rooms. Alarm/detectors must be maintained free of dust and debris which can interfere with operation. They should be installed per manufacturer's instructions . While it is primarily fuel burning appliances that produce carbon monoxide, CO is also produced from electric appliances like toasters and ranges (especially ovens on self clean cycle).
- Please be aware that residential Carbon Monoxide detectors are cumulative and are designed to not sound with low levels of carbon monoxide. Some people are more susceptible than others to low levels of carbon monoxide and I consider it prudent to familiarize yourself with the symptoms/warning signs of Carbon Monoxide. Detectors that meet the UL-2034 requirements for detectors installed in residential construction are not allowed to sound at continuous CO levels up to 30 ppm, 70 ppm for 4 hours, 150 ppm for up to 50 minutes and 400 ppm for up to 15 minutes. CARBON MONOXIDE
- A good low level, UL-2034, 10 year alarm is made by Defender.
- Combination type alarms can be problematic even while meeting "legal requirements" for installation. Carbon Monoxide detectors in conjunction with Ionization type smoke detectors is problematic due to the poor ion technology (see links under smoke alarms previous to this section). The devices also can have different life spans. For best protection, combination type alarms should not be used, even though this is a standard recommendation of manufacturers. The International Association of Fire Fighters (IAFF) specifically recommends against installing combination alarms. Combination type alarms are required to be UL-217 and UL-2034 listed.
Smoke Alarms Noted: Installed where currently required
Smoke Alarms: Present
At the time of inspection smoke alarms are not tested. I recommend that prior to move-in, that all smoke alarms be tested according to manufacturer's recommendations and that their batteries be replaced. It is recommended that smoke alarms that are older than 5-7 years should be replaced by a licensed electrical contractor if they are hard-wired; and replaced by the building owner/handy-person if they are battery operated.
- For optimum safety, hard-wired smoke alarms with backup batteries are recommended. At least one smoke alarm should be installed on each floor of the building. Alarms must be maintained free of dust and debris which can interfere with operation.
- Smoke alarm technology is evolving and current wisdom is recommending that only Photoelectric smoke alarms be installed in the building due to the nuisance tripping and other human factors involved with misuse and maintenance associated with Ionization type smoke alarms. It is not possible in the context of the building inspection to determine what types of alarms are installed in the building. You are encouraged to install and maintain any type of alarm in the building and you are encouraged to upgrade alarms to photoelectric type alarms. See the following link for a discussion of Ionization vs. Photoelectric Alarms: Photo-Electric Smoke Alarms and Silent Alarms; Deadly Differences.
- After June 30, 2021 all smoke alarms will be required to meet the 9th (the 8th was never adopted) edition of UL 217. These alarms are designed to reduce issues with previous versions and will be more responsive to multiple kinds of fire scenarios as well as address nuisance tripping issues of previous versions.
- In anticipation of the adoption of the 8th edition of UL 217, Kidde produced a dual sensor alarm that is purported to meet those standards, but given those standards were never adopted, they may or may not be an improvement over just stand alone photo-electric type alarms.
SMOKE ALARM Maintenance
- Clean regularly. Dust and debris will interfere with normal operation.
- Replace batteries at least once a year---or better yet install 10-yr type batteries.
- Schedule regular maintenance and tests. The Consumer Products Safety Commission recommends checking these alarms every Spring & Fall time change. Tests should be performed according to manufacturer's instructions.
- It is not usually possible in the context of a building inspection to determine whether smoke alarms are Ionization type or photoelectric type.
- Installation Recommendations from the National Fire Protection Association
I recommend upgrading the smoke and carbon monoxide (CO) alarm systems at this time to improve the home’s overall fire and CO safety. Proper placement and regular maintenance are key to keeping that protection reliable over time. For optimal alarm placement and any additional safety recommendations, consider consulting your local fire department or a fire safety professional. Test all alarms monthly, replace batteries annually (unless using 10-year sealed-battery models), and replace the entire unit every 10 years or per the manufacturer’s stamped date.
- Photoelectric smoke alarms - Replace existing smoke alarms with photoelectric models, which are better suited to residential use than ionization-type alarms, offering faster response to smoldering fires (the most common type in homes), improved accuracy and reliability, and fewer false alarms, especially when cooking.
- Combination Smoke/CO Alarms - Consider dual-sensor devices that detect both smoke and carbon monoxide for efficient protection.
Pest Related Conditions
Possible wood-destroying organism (WDO) activity was noted in the basement - see basement laundry room cabinets. Specifically, I observed what appeared to be frass (insect droppings/debris typically associated with wood-boring insects such as carpenter ants or wood-boring beetles). This can indicate past or present insect activity in the area. The identification and evaluation of wood-destroying organisms is beyond the scope of a standard home inspection, which is visual and non-invasive. I recommend further evaluation by a licensed pest control operator or WDO inspector to determine the type of activity, whether it is active, the extent of any damage, and appropriate treatment.
Kitchen
Sinks and Faucets
Tested: Tested
A slow drain was noted in the kitchen sink. Hire a qualified plumber to further evaluate and correct the slow drain as needed for proper drainage.
Cabinets and Countertops
Countertop Material: Stone slab
Cabinet Material: Wood
Most Common: Adjust Cabinets
Cabinet doors and drawers made contact during use and were in need of general adjustment. This contact can damage finishes and materials over time. I recommend adjustments as needed to improve functionality.
Ventilation Method
Ventilation Findings: Fan Ducted to Exterior
Appliances
Refrigerator: Operating
Dishwasher: Tested through a cycle
Dishwasher Air Gap: None Noted
Range, Oven and Cooktop: Electric
Disposer: Operated
Thermal Images: All Working
These thermal images show the appliances were tested and found to be working at the time of inspection.
An air gap is recommended to protect the dishwasher from accidental contamination if the sewer line were to back up. If an air gap cannot be installed, at least run the drain line above the level of the sink drain to create a high loop. This was an older way of protecting the dishwasher. Hire a licensed plumber to install an air gap.
General Kitchen Condition
Overall Kitchen: Ok
The kitchen and its components were tested and found to be functional at the time of inspection. Notable exceptions will be noted in this report.
Inspection Limitations – Kitchen Appliances and Components:
- Inspection of appliances and kitchen components is limited to a visual review and basic operation of built-in or permanently installed appliances using normal operating controls, when accessible and safe to do so.
- Appliances are not tested for performance, calibration, or the effectiveness of different modes, functions, or cycles.
- This inspection does not include evaluation for manufacturer recalls, concealed or inaccessible components, or future reliability of appliances.
- Portable appliances, countertop appliances, ice makers, water dispensers, and specialty features such as smart controls, timers, and self-cleaning functions are outside the scope of this inspection.
- Gas shut-off valves, electrical connections, exhaust ducting, and plumbing hookups were not disassembled to verify installation details or code compliance.
- No representation is made regarding the life expectancy of any appliance.
Primary Bedroom Bathroom
Sinks and Cabinets
Sink Testing: Tested
Toilet
Toilet Testing: Tested
Bathtub / Shower
Tub & Shower Testing: None Noted
Bathroom Ventilation
Ventilation Type: Bath Fan, Operable Window
General Bath Condition (Finishes, Walls, Flooring, etc)
Overall Condition: Standard - Typical Condition
Limitations: Testing Note
During the inspection, bathroom fixtures and surfaces were inspected and tested where access allowed, including operating all accessible plumbing fixtures, using a moisture meter around toilets and shower enclosures to check for hidden leaks, and testing for loose tiles and finishes in shower and tub enclosures where applicable. All visible components were checked for proper function, and ventilation fans were operated from standard controls, though actual airflow and exterior vent termination could not be fully confirmed.
Please note that this inspection is non-invasive, no destructive testing is performed, so hidden areas behind walls, under floors, or beneath finishes could not be assessed. Portions of piping, waterproofing, venting, and subflooring located behind finished surfaces were not accessible for inspection, and personal belongings and furnishings present at the time may have further limited full access to some fixtures and finishes. Bathtub overflow drains were not tested, in order to avoid potential damage to finishes. Fixtures were tested with normal water flow, which does not simulate prolonged or high-volume use and may not reveal minor leaks or issues that develop over time.
The inspection provides a snapshot of the plumbing system's condition at a specific moment; daily use may reveal issues not apparent during a brief inspection. Some defects, such as persistent moisture buildup, slow leaks, shower pan issues, or overflow drain leaks from gasket deterioration, might not be visible during a single inspection, even in well-installed systems.
I recommend regular monitoring and timely maintenance of bathroom finishes, caulking, and grout to help prevent future moisture issues and larger repairs. When using bathtubs, avoid overfilling and pushing water into the overflow drain, and monitor all plumbing fixtures closely after moving in. I encourage reporting any changes or concerns early, as prompt attention can help keep small problems from becoming larger ones.
This process and these limitations apply to all bathrooms in the home.
Upstairs Hallway Bathroom
Sinks and Cabinets
Sink Testing: Tested
Most Common: Sink Cracked - Monitor
Toilet
Toilet Testing: Tested
Bathtub / Shower
Tub & Shower Testing: Tested
Most Common: Several Concerns - See List
A few concerns were noted with the bathtub and its installation - see list below. Hire a licensed plumbing contractor to evaluate and repair these conditions as deemed necessary.
Observations
- The shower arm was loose and did not adequately support the shower head.
- The bathtub had been modified in a manner that no longer kept it watertight.
- Caulking/grout in the bathtub surround was exposed. Improve as needed to your satisfaction.
Bathroom Ventilation
Ventilation Type: Bath Fan
General Bath Condition (Finishes, Walls, Flooring, etc)
Overall Condition: Showed Wear Overall - Update to Your Satisfaction
Basement Bathroom
Sinks and Cabinets
Sink Testing: Tested
Toilet
Toilet Testing: Tested
Bathtub / Shower
Tub & Shower Testing: Tested
The tile shower did not drain effectively during use, and I noted water pooling on the floor - see the video below. This often indicates a partial drain blockage or inadequate slope in the shower floor. I recommend having the drain cleared and the floor slope evaluated by a qualified plumber or tile contractor, with re-sloping if needed to correct the drainage.
Bathroom Ventilation
Ventilation Type: Bath Fan
General Bath Condition (Finishes, Walls, Flooring, etc)
Overall Condition: Standard - Typical Condition
Attic
Attic Access
Method of Inspection: No access
This home has a low-slope roof with no accessible attic or roof cavity. As a result, the roof structure, framing, insulation, underside of the roof sheathing, and concealed ventilation could not be inspected, and any conditions within the roof cavity - such as prior leakage, moisture, inadequate insulation, or structural concerns - could not be evaluated.
Structure & Basement
Foundation
% of Foundation NOT Visible: 70%
Evidence of Seismic Protection: Not Visible
Building Configuration: Basement
Foundation Description: Poured concrete
The foundation was a poured (cast-in-place) concrete foundation. This is a common and durable foundation type, formed by pouring concrete into temporary forms to create continuous, monolithic walls.
Floor, Wall and Ceiling Framing
Wall Framing: Not visible
Wall Sheathing: Plywood, Not visible
Floor Framing: Partly visible, 2x8
Sub-Floor Material: Partly visible, Plywood
Ceiling Framing: Not visible
This inspection is a visual evaluation of the readily accessible components of the home and does not constitute an engineering or structural adequacy assessment. It is not intended to determine the structural capability or load-bearing capacity of any component or system. No warranty, guarantee, or certification of future performance, structural soundness, or service life is expressed or implied.
Basement
Information: Full
Basement Moisture
Observations: None noted
No visible moisture was noted in the basement at the time of the inspection. However, how a basement will perform over time with respect to moisture is impossible to predict during a one-time visual inspection. I recommend monitoring the area during periods of heavy rainfall, and keeping all gutters and downspouts clean and draining well away from the home - ideally discharging at least 5 to 6 feet from the foundation.
I did not observe any moisture staining or related issues while inspecting the basement. Conditions had been reasonably dry at the time of the inspection, however, and the materials on the basement portion of the foundation appeared to be newly installed - so how the space performs under sustained wet weather can’t be fully determined from a one-time inspection.
Older basements often experience seasonal dampness because modern waterproofing standards weren’t in place when they were built. Unlike contemporary foundations - which typically include exterior concrete sealers and water-diverting membranes - older foundations generally lack these measures. Some older basements stay dry thanks to favorable site conditions and good soil drainage, but with a basement of this age it’s wise to anticipate the possibility of moisture over time. The full extent of any such conditions can be difficult to assess during a standard visual inspection, so I recommend consulting a licensed contractor for repair options/recommendations if moisture appears.
Modern basement waterproofing techniques include:
- Exterior concrete sealer application
- Waterproofing membrane installation
- Footing drain systems at the base of the foundation
Sewer Scope Overview
Inspection Information
Information: Information
Please review all comments and recommendations in this report before the close of escrow, including any recommendation for further evaluation by a licensed plumber or sewer contractor. I am not a licensed plumber. A qualified sewer professional can confirm findings, explain repair options and help you plan next steps. The sewer line is one of the most important and least visible parts of a home, which is why I recommend a sewer scope for every home purchase. Please give me a call anytime with questions about your results.
Smoke Testing
Local sewer utilities periodically smoke test their systems to find leaks and defects in the main line, in the side sewers that connect to it, and in the drain and vent piping inside homes. The smoke is non-toxic to people, pets and plants. If a defect is found in the side sewer serving this property, the utility can require the owner to repair it as a condition of continued service. Any defect noted in this sewer scope is worth addressing with that in mind.
What to Know About Your Sewer Line
- Not perfect does not mean failing. Most older sewer lines show some wear. A line that carries waste to the main without backing up is generally doing its job, even if it is not in new condition.
- Bellies (low spots). Sags in the line can hold water and hide part of the pipe from the camera. With normal use they rarely cause blockages, but grease, food waste from a disposer, eggshells, heavy toilet paper use and low-flow toilets can build up in a belly over time, and the line may need periodic cleaning.
- Offset joints. Pipe joints that have shifted out of alignment can still drain well. Depending on how severe they are, offsets may only need monitoring, or they may need repair, lining (sleeving) or replacement.
- Roots. Roots in the line should be cleared, and the line should be re-scoped afterward to confirm it is clear. Ask whoever cleans the line to provide video verification.
- Cleanouts. Many older homes were built without an exterior cleanout, which can limit how much of the line can be seen. Installing a cleanout allows the full line to be scoped and makes future cleaning much easier. Talk with your agent about whether to request one as part of your transaction.
- Know your options. Many sewer findings have more than one reasonable solution, from monitoring and periodic cleaning to spot repair, lining or full replacement. Sewer service companies often lean toward repair or replacement, so ask for options, consider a second opinion for major recommendations, and talk through the results with your agent before deciding what works for you.
Sewer Inspection Report
Access Point
Access Point: Cleanout
SIDE SEWER ACCESSED THROUGH CLEANOUT
I accessed the side sewer through a 3 inch, ABS cleanout. Location: Laundry Room
Side Sewer Type (Public/On-Site)
Side Sewer Type: Public Sewer System
PUBLIC SEWER SYSTEM
The side sewer serving this property is connected to a public sewer system.
Sewer Scope Findings
Pipe Materials: Pipe Materials
I noted the following pipe material(s), listed in the order I encountered them moving from the point of access toward the main sewer line:
Pipe Materials
- Plastic (PVC or ABS) — Modern plastic pipe, common since the 1970s. Expected service life is roughly 50 to 80 years or more.
- Cast Iron — Strong, durable pipe that often lasts 50 to 100 years. It usually fails from internal rust, scaling and corrosion rather than sudden cracking.
- Concrete — Very common in the 1950s and 1960s. Life expectancy is 75 to 100 years, but it can be as short as 35 years depending on soil conditions.
Tie-In Depth (Main or Septic Tank): Approximate Depth
APPROXIMATE DEPTH TO MAIN OR SEPTIC TANK TIE-IN
The side sewer's tie-in to the main or the septic tank is approximately 10 feet below grade.
Sewer Scope Findings: Exposed Aggregate (Moderate)
Overall Summary: Summary - Several Concerns
The side sewer was accessed from a cleanout in the laundry room; no other portion of the pipe or connecting lines was inspected. From that access point, I was able to push the camera all the way to the sewer main connection at the street. During the video inspection I noted a few concerns needing attention - see list below. Hire a licensed plumbing contractor who specializes in side sewer repair for a further evaluation and all needed repairs.
Observations
- What appeared to be localized damage was noted at - 55 feet. I could not 100% due to to roots blocking my view. This was located in the driveway and marked with a green dot at a depth of about 9ft.
- I found severe root intrusion at multiple areas blocking more than half of the pipe. Roots this large are likely restricting flow now and can cause backups and further pipe damage.
- What appeared to be a hole in the materials was noted at a WYE - 17 feet.
- A sag/belly was noted at 19-22 feet that was collecting water.
- Moderate exposed aggregate in the concrete was noted all the way around the inside of the pipe. The inner surface has worn away, exposing the gravel in the concrete. Drainage is likely ok for now, but the pipe wall is getting thinner and I can't tell how much is left. I recommend having the line re-scoped every 3 to 5 years and planning for eventual lining or replacement.
- A WYE was noted at the cast iron to concrete material connection at 2 areas - I could not confirm what these were for.
Materials (In Feet)
- 0-16 3" Cast Iron
- 16-71 4" Concrete
Sewer Scope Video
VIDEO: Video
Here are the videos recorded during your sewer scope inspection - see below. If you have any questions or need help viewing the videos, don’t hesitate to reach out!

West Inspect LLC
(360) 303-0410
Please follow this link to your video on YouTube: LINK
Common Side Sewer Repair Processes
Common Side Sewer Repair Processes
Repair Description: Description
What Is a Side Sewer?
A side sewer is the privately owned pipe that carries wastewater from a building's sinks, drains and toilets to the public sewer main, usually under the street. As the property owner, you are responsible for the side sewer all the way to the connection at the public main, including the section beyond your property line. Some homes share a side sewer with a neighbor, which means repairs may need to be coordinated between owners. The diagrams below show where the side sewer runs and which portion the property owner maintains. (Diagrams courtesy of Seattle Public Utilities. Responsibility at the main can vary by city, so check with your local sewer utility.)
Common Side Sewer Repair Methods
There are several ways to repair, replace or rehabilitate a side sewer. Every line is different, and not every method works for every situation. An experienced sewer contractor can recommend which options suit this property.
Open cut (dig and replace)
- The most common method. The old pipe is dug up and replaced with new pipe. It can correct any defect, including sags, but it disturbs everything above the line, so it is less practical when the line is deep or runs under driveways, patios, landscaping or other improvements.
Pipe bursting
- A bursting head is pulled through the old pipe, breaking it apart while a new pipe is pulled in behind it. Only a small pit is dug at each end, so surface improvements are mostly left undisturbed. It does not work well in pipes with multiple bends or pipes that are badly crushed, and because the new pipe follows the path of the old one, it will not correct sags.
Cured-in-place pipe (CIPP) lining
- A resin-soaked liner is inserted into the existing pipe, inflated, and cured until it hardens into a new pipe inside the old one. It is usually installed through a cleanout, so little or no digging is needed. Because the liner takes the shape of the old pipe, it is not suitable for collapsed or badly out-of-round pipe, lines with multiple bends, or lines with sags.
Spot repair
- A single damaged section is dug up and replaced. This works well when the rest of the line is in good condition. If defects are found in several places along the line, a full replacement or lining is often the better long-term choice than repeated spot repairs.
Checking Out Procedure
Check Out List
Checkout Note: Standard checkout disclaimer
Before leaving the property, I made a reasonable effort to return the home to the condition it was in when I arrived. This included turning off the lights and appliances I operated, returning the thermostat to its original setting, and closing and locking the windows and doors I opened. This checklist reflects the condition of the home at the time I left. I am not responsible for changes made by others after my departure, or for conditions involving items I did not operate. If anything appears out of place at your next visit, please contact me right away so I can help sort it out.
Lights: Off
Range and Oven: Off
Heating and Cooling: Restored to settings found - thermostat note
The thermostat was returned to the setting found at the start of the inspection. Thermostat schedules, programming and remote or smart-thermostat settings were not reviewed or changed. It may take some time for the home to return to its previous temperature.
Appliances: Off and finished cycles where tested
Windows: Closed and locked where tested
Doors: Closed and locked where tested
Water Fixtures: Turned off
Garage Doors: Closed
Additional Information
Information
Common Information: Washington State Standards Of Practice, Expectations
Home inspections in Washington State are performed under the Standards of Practice for licensed home inspectors (WAC 308-408C). These standards are the minimum requirements every home inspector in the state must follow, and they explain what is and is not included in your inspection. You can read the current standards on the Washington State Legislature website here: Washington Home Inspector Standards of Practice.
Setting Reasonable Expectations
Setting Reasonable Expectations When Things Go Wrong
There may come a time when you discover something wrong with the house...
Living in a House Is Different From Inspecting One
Some problems can only be discovered by living in a house - they can't be found during the few hours of a home inspection. For example, some shower stalls leak only when someone is actually showering, not when you simply turn on the tap. Some roofs and basements only leak under specific conditions. Some problems only surface once carpets are lifted, furniture is moved, or the whole family is trying to shower at once.
No Clues
Some problems may have existed at the time of inspection with no visible clues. Our findings are based on the home's condition as observed; if there's no evidence of a problem, we can't foresee one.
We May Leave Some Minor Things Out
Minor issues we do note are typically discovered while looking for more significant concerns - we mention them simply as a courtesy. The goal of the inspection isn't to catch every minor problem; it's to catch the significant ones that affect real estate decisions.
Limitations
Weather, temperature, occupant belongings, and limited access can all restrict what we're able to see during an inspection.
The Wisdom of Hindsight
Once a problem manifests, 20/20 hindsight makes it look obvious. We look for evidence of past issues and flag conditions that could lead to future ones, but we can't predict the future.
A Long Look
Home inspections run on tight timelines. Fully evaluating every detail of every system would take considerably more time than a standard inspection allows.
We're Generalists
We're generalists, not specialists — a heating contractor knows more about heating, an electrician more about electrical systems. That's why we often recommend an expert to further evaluate and correct a system: we look for signs of a problem and point you toward someone who can fix it.
An Invasive Look
Problems often surface once trim boards or carpets are removed, or fixtures and cabinets are pulled out. A home inspection is a visual examination — we can't perform invasive or destructive testing, and we can't report on defects we can't see.
Not Insurance, But Education
A home inspection is designed to improve your odds, not eliminate all risk — it shouldn't be treated as an insurance policy. Our goal is to educate you about your home and provide guidance and peace of mind going forward.
Conclusion of Your Report
Since we never know who will occupy or visit a property — children, elderly relatives, or anyone else — we recommend the following general safety practices:
- Install and monitor smoke and carbon monoxide alarms.
- Identify all escape and rescue paths, and rehearse an emergency evacuation.
- Never service electrical equipment without first disconnecting its power source.
- Set water heater temperatures to prevent scalding.
Get to know your home so you can more easily recognize when something isn't right.
We've made every effort to give you an accurate assessment of the property's condition and to flag any significant defects or adverse conditions. As a homeowner, expect problems to arise over time - a regular home maintenance schedule is one of the best things you can do for your home.
Please use us as a resource going forward. If you'd like a maintenance inspection, or an unbiased second opinion on repairs or updates down the road, we're happy to help. We also recommend getting at least two professional opinions for any defects or recommendations mentioned in this report.
Thank you for taking the time to read this report - please call with any questions. We're always working to improve our service and this report, and we're committed to the highest standards in the industry, treating everyone with kindness, courtesy, and respect.
Summary - Evaluate by licensed contractors
Primary Concerns
- SIR-5 Sewer Inspection Report:
The side sewer was accessed from a cleanout in the laundry room; no other portion of the pipe or connecting lines was inspected. From that access point, I was able to push the camera all the way to the sewer main connection at the street. During the video inspection I noted a few concerns needing attention - see list below. Hire a licensed plumbing contractor who specializes in side sewer repair for a further evaluation and all needed repairs.
Observations
- What appeared to be localized damage was noted at - 55 feet. I could not 100% due to to roots blocking my view. This was located in the driveway and marked with a green dot at a depth of about 9ft.
- I found severe root intrusion at multiple areas blocking more than half of the pipe. Roots this large are likely restricting flow now and can cause backups and further pipe damage.
- What appeared to be a hole in the materials was noted at a WYE - 17 feet.
- A sag/belly was noted at 19-22 feet that was collecting water.
- Moderate exposed aggregate in the concrete was noted all the way around the inside of the pipe. The inner surface has worn away, exposing the gravel in the concrete. Drainage is likely ok for now, but the pipe wall is getting thinner and I can't tell how much is left. I recommend having the line re-scoped every 3 to 5 years and planning for eventual lining or replacement.
- A WYE was noted at the cast iron to concrete material connection at 2 areas - I could not confirm what these were for.
Materials (In Feet)
- 0-16 3" Cast Iron
- 16-71 4" Concrete
Repairs
- G-1 Grounds:
Several simple conditions and due diligence items were noted with the downspouts around the home - see list below. Repair these items as feasible to ensure proper moisture mitigation around the home.
Observations
- Extend the downspouts away from the home at many places - south side.
- A drain was noted below the west-side sunroom that did not appear robust enough to adequately manage moisture in this area. I observed evidence of water buildup (old debris) around the area, and the seller indicated that a puddle does form here. I recommend consulting a licensed drainage contractor for options to upgrade this drainage system.
- Dented and damaged gutter noted at the sunroom.
- G-3 Grounds:
The exterior stairs were missing a graspable handrail for safety - see west side. Stairs with four or more risers need a handrail. Have a qualified contractor build suitable railings to reduce the potential for falls.
- E-1 Exteriors:
The exterior siding materials showed multiple areas of deferred maintenance and localized damage – see list below. Hire a licensed contractor for a further evaluation and to come up with a cohesive plan for repairs and updating.
Observations
- Checked/damaged fascia board materials - several sides.
- Faded/peeling paint throughout the exterior.
- Staining at the eaves was faded and in need of re-application.
- Torn soffit screening - north side near chimney.
- Window trim needs paint – north side.
- Checked and sun damaged materials - south side at garage.
- DPB-2 Decks, Porches & Balconies:
Several conditions were noted with the deck installation - see the list below. Some of these items may not have been required under the building standards in place when the deck was originally built, but they remain worthwhile to retrofit now for improved safety and durability. I recommend having a licensed contractor further evaluate these conditions and perform all needed repairs.
Observations
- Missing flashing at the ledger board connections.
- Moisture damaged materials at the cantilever ledger board connection due to missing flashing.
- The deck is attached to a floor cantilever. This can be an unreliable connection as there is no wall below the rim joist for support. Consult with a qualified contractor about options for repair/improvement to ensure safe and reliable performance. Several options for strengthening this connection are using lateral load ties and building a post and beam system below the deck so it is self supporting and not reliant on the house connection.
- Moisture damaged support posts below sunroom - SW corner.
- RCG-3 Roof, Chimney & Gutters:
The roof appeared to be a 2008 or so installation but had a few items needing attention - see the list below. I recommend having a licensed roofing contractor further evaluate and complete these repairs to ensure reliable, long-term performance.
Observations
- Multiple areas of the roofing showed rippling and/or air trapped beneath the materials. While some minor rippling can be common, the extent noted here appeared excessive. This can result from improper installation (such as installation over an uneven deck or without proper acclimation), inadequate underlayment, or moisture beneath the shingles, and it may affect the roof’s appearance and long-term performance.
- Drainage appeared to be insufficient near the north chimney, where debris buildup was observed.
- Sealant at the solar tube was exposed and needed to be redone.
- The center chimney masonry showed wear and needed repairs.
- Organic debris buildup was noted at the roof covering. Due to the amount of nearby trees, diligent ongoing maintenance will be needed.
- RCG-4 Roof, Chimney & Gutters:
The skylight design for the sunroom is an older style that requires diligent, ongoing maintenance. I observed portions of the caulking that had failed and are in need of maintenance at this time. I recommend consulting a licensed glazing specialist for repairs and updating where feasible.
Observations
- Multiple areas of moisture staining were noted below the top glass panels. This may indicate active leakage or a prior, since-resolved condition.
- A cracked window pane was noted. I recommend replacing it as needed to maintain a proper seal and prevent further cracking.
- Multiple failed seals were noted throughout the sunroom. Failed seals can allow air and moisture intrusion and often show as fogging or condensation between panes.
- EDFW-4 Electric Distribution & Finish Wiring:
Several conditions were noted in the home's wiring system - see the list below. I recommend evaluation and repair by a licensed electrical contractor as needed. Please note that electrical systems are largely concealed within walls, ceilings, and other finished areas, so additional latent or hidden defects may exist that were not visible during this inspection.
Observations
- Missing an exterior rated cover plate - west side under deck.
- A GFCI receptacle did not have power and would not reset - SE corner.
- Two light fixtures in the kitchen did not function.
- Exposed wiring - hallway closet ceiling.
- Missing GFCI protection near the basement sink.
- WH-6 Water Heater:
The water heater temperature was set too low at the time of inspection - just 107 degrees F. About 120 degrees F at the fixtures is the generally recommended temperature, so I recommend adjusting the water heater setting as needed. For best practice, many plumbers set the tank to 130-140 degrees F and install a tempering (mixing) valve so water is delivered to the fixtures at a safe 120 degrees F. The higher tank temperature helps reduce the risk of Legionella bacteria developing in the tank.
- LAP-4 Laundry & Additional Plumbing:
The dryer vent for the garage laundry area did not terminate to the exterior as it should. Dryer exhaust vented into the garage (rather than outside) releases significant moisture and lint into the space, which can raise humidity and create a fire hazard from lint accumulation. I recommend having the dryer vent properly routed and terminated to the exterior by a qualified contractor.
- I-8 Interior:
A failed window seal was noted in the glazing at 1-2 windows, and more may become apparent as exterior conditions change. The symptoms often take the form of condensation between the panes of glass and these failures are more a cosmetic consideration than a functional one. The failure does not significantly affect the thermal insulation value of the window, however, the fog cannot be removed by normal cleaning. There is no simple fix for this condition, short of replacing the entire glazing unit. Not all windows may be represented in the photos. I recommend evaluation and replacement of any failed windows as desired. Please follow this link for more information - LINK.
Locations
- Lost seal - basement NW family room.
- K-2 Kitchen:
A slow drain was noted in the kitchen sink. Hire a qualified plumber to further evaluate and correct the slow drain as needed for proper drainage.
- UHB-3 Upstairs Hallway Bathroom:
The toilet was cracked near the mounting bolts. A cracked toilet base can leak at the floor and is considered an unsanitary condition, and cracks in this area can worsen under normal use. I recommend replacing the toilet by a qualified plumber before continued use.
- UHB-4 Upstairs Hallway Bathroom:
A few concerns were noted with the bathtub and its installation - see list below. Hire a licensed plumbing contractor to evaluate and repair these conditions as deemed necessary.
Observations
- The shower arm was loose and did not adequately support the shower head.
- The bathtub had been modified in a manner that no longer kept it watertight.
- Caulking/grout in the bathtub surround was exposed. Improve as needed to your satisfaction.
- BB-2 Basement Bathroom:
The tile shower did not drain effectively during use, and I noted water pooling on the floor - see the video below. This often indicates a partial drain blockage or inadequate slope in the shower floor. I recommend having the drain cleared and the floor slope evaluated by a qualified plumber or tile contractor, with re-sloping if needed to correct the drainage.
Minor Repairs
- E-2 Exteriors:
The garage exterior door was delaminating and should be replaced in the near term.
- E-4 Exteriors:
A hose bib leaked under pressure when tested. Hire a licensed plumbing contractor for repairs. This often requires tightening the packing around the handle stem and could be a straightforward repair.
Locations
- Rear side
- ES-6 Electric Service:
Multiple double-lugged neutrals were noted at the busbar - this is where two conductors are terminated under a single lug. Neutral (grounded) conductors in particular should each land on their own individual terminal, because a shared neutral lug can loosen, overheat, and create an unreliable or unsafe connection. It can also make it unsafe to service a single circuit, since loosening the lug affects more than one conductor. I recommend repair by a licensed electrical contractor so each neutral is terminated on its own terminal.
- Code Reference: The National Electrical Code (Article 408.41) requires each grounded (neutral) conductor to terminate at an individual terminal not shared with another conductor. Washington adopts the NEC as part of its electrical code.
- P-6 Plumbing:
The supply pipe insulation was incomplete in the garage at many areas. Be sure all supply lines in unheated spaces have been adequately insulated to protect from freezing conditions that could damage the pipes and to prevent heat loss.
- K-3 Kitchen:
Cabinet doors and drawers made contact during use and were in need of general adjustment. This contact can damage finishes and materials over time. I recommend adjustments as needed to improve functionality.
- K-5 Kitchen:
An air gap is recommended to protect the dishwasher from accidental contamination if the sewer line were to back up. If an air gap cannot be installed, at least run the drain line above the level of the sink drain to create a high loop. This was an older way of protecting the dishwasher. Hire a licensed plumber to install an air gap.
Maintenance Items
- G-5 Grounds:
Trees, shrubs or other vegetation were touching or growing close to the home. This is common and easy to fix with regular pruning and maintenance. Prune trees, branches and vegetation back at least six feet from the building, including any limbs over the roof. Trim them regularly as part of routine home maintenance to keep that space open.
Plants against the siding and roof hold moisture and block airflow and sunlight, so the exterior stays damp longer after rain. In our Pacific Northwest climate, that dampness makes the area a condition conducive to wood destroying organisms such as rot fungi, carpenter ants and other wood-boring insects. Branches touching or hanging over the roof also give rodents and other pests an easy path onto the roof and into attic vents or other small openings. Overhanging branches can also drop leaves and needles that clog gutters and wear down the roof.
- RCG-6 Roof, Chimney & Gutters:
The gutters and downspouts needed common repairs/maintenance going forward - see list below. Implement repairs to ensure they are clear of obstructions, well fastened, leak free and sloped to drain.
Observations
- Multiple portions of the gutters were full of organic debris.
- Loose gutters noted that needed to be secured.
- I-2 Interior:
The hardwood floors were scratched and the finishes were wearing in some areas. Hire a wood floor specialist to evaluate and refinish the floors to your satisfaction.
Information
- Options typically include: a complete sand and finish which, if there is enough material on the wood, can make the floors look new - or a simpler option of just adding more finish and leaving many of the scratches and dings.
- I-6 Interior:
Doors throughout the home were in need of adjustment and general maintenance - see the list below. These are typically minor items, and I recommend having a handyperson adjust and repair the doors as needed.
Observations
- Missing doorstops at multiple closet doors.
- The north bedroom closet door and entry door rubbed on their frames.
- The closet door in the NE bedroom was missing a panel and the track was damaged.
- The primary bathroom door rubbed on its frame.
- Damaged door - NE bedroom.
- The basement NE bedroom door did not latch.
Improve & Upgrade
- G1-2 Garage:
To improve fire safety between the garage and the house, a minimum of 1/2 inch gypsum board (sheetrock) is needed on the garage side of walls that separate the garage from living spaces. This fire separation is specifically designed to slow the spread of fire from the garage to the rest of the home, significantly increasing occupant safety. In contrast, older homes with wood walls in the garage do not meet current fire safety standards and are not considered compliant with modern code requirements.
- G1-3 Garage:
The installed garage door was an older tilt-up (one-piece swing) design, which is generally less reliable and convenient than newer sectional models. This style swings outward as it opens, so a vehicle or objects must be parked far enough back to allow the door to open fully. These older doors also typically lack the safety features of modern openers, such as auto-reverse and photo-eye sensors. I recommend considering an upgrade to a newer sectional door and opener with current safety features, as desired.
- HV-6 HVAC & Ventilation:
The electric wall heaters were an older design, and upgrading to modern units is worth considering - see sunroom. Newer units offer improved efficiency and safety compared to the currently installed heaters. Consult with an HVAC contractor and/or licensed electrician for further information and upgrade options.
- HV-9 HVAC & Ventilation:
The installation of a mechanical ventilation system would be a logical upgrade for this home. As the home predates the requirement for this, there are several options, including a whole house fan on a timer exhausting air to the exterior and bringing in fresh air, a heat recovery ventilator (HRV) and so on. Consult with a licensed HVAC contractor about improvements to the home's ventilation design.
Information
- I-9 Interior:
Some windows in this home are older single-pane units with metal frames. These do not meet modern standards for safety glazing or thermal performance, which is common and expected in windows of this age. Metal frames also conduct heat and cold readily, so these windows tend to be less energy-efficient and more prone to condensation than modern assemblies.
Upgrading is optional rather than required - but improvements in comfort, energy efficiency, and safety may make it worthwhile. Full replacement with modern dual-pane units offers the greatest benefit, while a simpler alternative is to apply protective safety film to the existing glass to improve its impact resistance. I recommend consulting a qualified glazing or window contractor to review the existing windows and provide evaluation and upgrade options appropriate for the home.
- I-10 Interior:
The bedrooms in this home had escape and rescue openings that do not meet current standards. This is very common in older homes, as these requirements were not in place when the home was built, so it is considered a worthwhile safety upgrade rather than a defect. Current standards call for bedrooms to have a second means of escape in an emergency - typically a window, though a door can also satisfy this. Upgrading these openings would improve occupant safety, particularly for use as an emergency exit or for firefighter access. I recommend having a licensed general contractor evaluate the openings and update them where feasible.
Egress window - basic requirements:
- 20" minimum width
- 24" minimum height
- 5.7 sq. ft. net clear opening (5.0 sq. ft. at grade level)
- Sill no more than 44" above the floor
- Opens easily without keys or tools
Window well (if below grade):
- 9 sq. ft. minimum area
- 36" minimum projection and width
- If deeper than 44": a permanently affixed ladder or steps, usable with the window fully open
Due Diligences
- G-4 Grounds:
Trees were noted near the home and it is recommended to have a certified arborist conduct a comprehensive inspection of them. An ISA-certified arborist can evaluate tree health, identify any hidden issues like disease, decay, or weak branches, and provide maintenance recommendations tailored to your property. Regular professional evaluations help prevent property damage, especially if tree care hasn’t been performed in recent years. Pruning by a qualified arborist can also reduce wind stress, eliminate pest entry points, and support both safety and long-term property value.​
Recommendations
- Hire an ISA-certified arborist to evaluate tree health and safety, especially if pruning or removal may be needed.​
- Larger or overhanging trees may require pruning to reduce wind sail effect and minimize storm damage risks.​
- Regular inspections, ideally every 1–3 years, help detect issues early, including disease, dead limbs, and root problems.​
- Proper pruning discourages rodents and pests from accessing or nesting near your home.​
- DIY pruning is not always recommended as professionals have the experience, insurance, and tools to work safely near structures.​
- FSD-1 Fuel Storage & Distribution:
There is evidence that this home was once heated with oil, as indicated by the old oil lines noted at the basement of the house. This likely means that a heating oil storage tank is present or was once buried on the property. These tanks were common in older homes and are not unusual to encounter today.
Recommendations
- Ask the seller for documentation showing that the tank was properly decommissioned or removed. In most cases, a fill valve is cut off once decommissioning is complete. If records are unavailable, consider hiring a tank‑locator service to verify whether a tank remains underground. This is a preventive step to help ensure there are no hidden environmental liabilities, as oil leaks from old tanks are much easier to address when discovered early.
- If a tank is found, have it evaluated and properly decommissioned or removed by a qualified contractor before closing.
More information
- G1-1 Garage:
Microbial-like staining patterns were noted on the wall of the garage. These are likely from a prior moisture condition. Testing at the time indicated the wall was dry. I recommend using a stain killing primer and paint to seal this stain.
- ES-1 Electric Service:
No permit stickers or paperwork related to electrical work were found on the electric panel. Inquire with the seller for any additional information about this installation.
- ES-4 Electric Service:
The service neutral connection appeared to lack the barrel clamp (connector) typically present at this location. Because this connection is at the utility service entrance, I recommend consulting your local utility provider for further evaluation to confirm the connection is adequately rated and properly secured.
- EDFW-2 Electric Distribution & Finish Wiring:
The home’s electrical system, typical of pre-1962 construction, featured original ungrounded wiring. This type was commonly used in homes built before the 1960s and consists of two insulated conductors (hot and neutral) encased in a non-metallic sheath - often cloth or rubber, with some variations including additional paper insulation. While this was standard and acceptable at the time, it does not include a dedicated grounding conductor, which is now a standard safety feature in modern electrical systems.
Although ungrounded Romex-style wiring was an improvement over older systems like knob-and-tube, it does present some safety considerations. Without a grounding conductor, there is no dedicated path to safely carry a fault to ground, which can pose a shock or fire risk. In addition, many modern appliances and electronics are designed for grounded receptacles, and using them on ungrounded wiring can lead to improper operation or potential damage to the devices.
While this type of wiring is not uncommon in older homes, it’s something to be aware of. I recommend consulting a licensed electrician to discuss potential upgrades and improvements for added safety and compatibility with today’s standards - such as GFCI protection for ungrounded circuits, whole-house surge protection, and AFCI breakers.
Observations
- Multiple ungrounded receptacles were still in use - garage.
- Original cloth wiring noted above the electrical panel.
- Grounded receptacles were used on ungrounded wiring throughout the home.
- P-9 Plumbing:
A corroded metal P-trap was noted below the basement sink. Corrosion can weaken the trap over time and eventually lead to leaks. I recommend replacing it with a new trap (metal or PVC) as needed by a qualified plumber or handyperson.
- LAP-2 Laundry & Additional Plumbing:
The clothes washer and dryer appeared to be older units. Both were operating at the time of inspection; however, due to their age and visible appearance, upgrading these appliances at your convenience may be worth considering.
Water Supply Connectors
- Replace existing hoses with stainless steel-braided ones
- Install flood-stop devices for leak prevention
- Replace hoses every 3-5 years, even if they appear intact
Drain Piping
- Secure the drain pipe to prevent movement during use
- Fasten it to nearby water pipes or wall studs
- Use appropriate clamps or brackets for a stable connection
- HV-11 HVAC & Ventilation:
A wood burning fireplace and wood stove were noted in the home. The NFPA (National Fire Protection Association) recommends an annual inspection of all chimneys, fireplaces, solid fuel-burning appliances, and vents. They also recommend an NFPA 211 Standard, Level II inspection upon sale or transfer of the property. A Level II inspection includes, not only cleaning the interior of the chimney pipe, but also the use of specialized tools and testing procedures such as video cameras, etc. to thoroughly evaluate the serviceability of the entire flue lining and fireplace/chimney system. If a chimney cleaning has not been performed over the past 12 months, such an inspection is recommended before closing and prior to first use for fire safety reasons - consult with a CSIA-certified chimney sweep for this inspection service. Implement any repairs as recommended.
Upgrades
- For improved energy efficiency, install glass doors for the front of the fireplace to reduce heat loss during winter months. Be sure to keep the flue damper inside the firebox closed as well. Chimneys are very good at sucking heat out of your house and glass doors and flue dampers help to slow this heat loss.
- I-3 Interior:
Water stains were noted on the ceiling near the chimney. These stains were tested with a moisture meter during the inspection and read dry at that time, which suggests the source may be from a prior, since-resolved condition rather than an active leak. I recommend asking the seller about any history of leakage in this area to better determine whether repairs are needed to prevent a recurrence. Once any source is confirmed resolved, the damaged sheetrock can be repaired and painted as needed for a proper cosmetic finish.
- I-4 Interior:
The interior entry stairs had non-standard riser heights - see short first step. The tallest riser should not exceed the smallest by more than 3/8ths of an inch. Have this further investigated by a licensed contractor and repaired as feasible; this can be tricky to repair sometimes.
- Please follow this link to current code information - LINK.
- I-13 Interior:
I recommend upgrading the smoke and carbon monoxide (CO) alarm systems at this time to improve the home’s overall fire and CO safety. Proper placement and regular maintenance are key to keeping that protection reliable over time. For optimal alarm placement and any additional safety recommendations, consider consulting your local fire department or a fire safety professional. Test all alarms monthly, replace batteries annually (unless using 10-year sealed-battery models), and replace the entire unit every 10 years or per the manufacturer’s stamped date.
- Photoelectric smoke alarms - Replace existing smoke alarms with photoelectric models, which are better suited to residential use than ionization-type alarms, offering faster response to smoldering fires (the most common type in homes), improved accuracy and reliability, and fewer false alarms, especially when cooking.
- Combination Smoke/CO Alarms - Consider dual-sensor devices that detect both smoke and carbon monoxide for efficient protection.
- UHB-2 Upstairs Hallway Bathroom:
The sink had cracks noted, but no leakage was observed after testing. I recommend monitoring the area, as cracks can expand over time and eventually lead to leaks. The sink can be replaced now as a precaution, or in the future as needed.
Inspection Notes Limitations
- GC-8 General Comments:
At the time of inspection, this property was unoccupied. Vacant properties present unique challenges for home inspections, particularly regarding plumbing and electrical systems that have not been in regular use. While these systems can be tested during the inspection, it's important to note that a one-time assessment differs significantly from regular use, making it difficult to predict how these systems will perform under normal conditions post-inspection.
Potential Issues in Vacant Properties:
Plumbing Systems
- Septic systems may initially function but fail under regular daily use
- Plumbing traps may show no signs of leaks during inspection but develop issues with active use
- Shower pans may only leak when subjected to the weight and movement of an occupant
- Seals for plumbing fixtures can dry out due to disuse, potentially leading to leaks when reactivated
Sewer Lines
- Root intrusion may allow water flow during testing but fail when processing waste and tissue, potentially causing backups over several days. A sewer inspection is always recommended.
Our Commitment
- We genuinely strive to conduct a thorough inspection by looking for indicators of past or existing problems. Our goal is to provide a realistic assessment of these systems' reliability based on the information available during the inspection. However, please understand that certain issues may only become apparent under regular use or over time. We recommend monitoring these systems closely upon occupancy and regular maintenance to ensure optimal performance and early detection of any potential issues.
- HV-5 HVAC & Ventilation:
Records for the heating/cooling system indicated it was serviced within the past year; consult the seller for documentation to confirm this to your satisfaction. The manufacturer recommends annual servicing, and I advise continuing with a yearly maintenance schedule by a licensed HVAC contractor, including inspection of the heat exchanger.
- A-1 Attic:
This home has a low-slope roof with no accessible attic or roof cavity. As a result, the roof structure, framing, insulation, underside of the roof sheathing, and concealed ventilation could not be inspected, and any conditions within the roof cavity - such as prior leakage, moisture, inadequate insulation, or structural concerns - could not be evaluated.
- SB-4 Structure & Basement:
I did not observe any moisture staining or related issues while inspecting the basement. Conditions had been reasonably dry at the time of the inspection, however, and the materials on the basement portion of the foundation appeared to be newly installed - so how the space performs under sustained wet weather can’t be fully determined from a one-time inspection.
Older basements often experience seasonal dampness because modern waterproofing standards weren’t in place when they were built. Unlike contemporary foundations - which typically include exterior concrete sealers and water-diverting membranes - older foundations generally lack these measures. Some older basements stay dry thanks to favorable site conditions and good soil drainage, but with a basement of this age it’s wise to anticipate the possibility of moisture over time. The full extent of any such conditions can be difficult to assess during a standard visual inspection, so I recommend consulting a licensed contractor for repair options/recommendations if moisture appears.
Modern basement waterproofing techniques include:
- Exterior concrete sealer application
- Waterproofing membrane installation
- Footing drain systems at the base of the foundation
Pest Conditions
- I-14 Interior:
Possible wood-destroying organism (WDO) activity was noted in the basement - see basement laundry room cabinets. Specifically, I observed what appeared to be frass (insect droppings/debris typically associated with wood-boring insects such as carpenter ants or wood-boring beetles). This can indicate past or present insect activity in the area. The identification and evaluation of wood-destroying organisms is beyond the scope of a standard home inspection, which is visual and non-invasive. I recommend further evaluation by a licensed pest control operator or WDO inspector to determine the type of activity, whether it is active, the extent of any damage, and appropriate treatment.
Receipt -- The Full Report
12345 68th Ave NW Seattle, WA 98125
| Residential Inspection Fee | $725.00 |
| Sewer Line Inspection Fee | $275.00 |
| $1,000.00 | |
| PAID |
West Inspect LLC
336 36th St. Suite #201
Bellingham, WA 98225
(206)-799-6084 & (360) 303-0410









 (1).png)


















